cc/td/doc/product/atm/ls1010s/wa4/11_3
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Checking the ASP Installation

Checking the ASP Installation

This chapter describes procedures for confirming the successful hardware installation and initial configuration of the ATM switch processor (ASP), and includes the following sections:

Troubleshooting

Problems with the initial startup are often caused by an interface processor or power supply that has become dislodged from the backplane or chassis power connector during shipment. Although over-temperature conditions rarely occur at initial startup, the environmental monitoring functions are included because they also monitor DC line voltages. At the initial system boot, verify the following:

When these conditions are met, the hardware installation is complete. If the startup sequence fails before these conditions are met, use the procedures in this chapter to isolate and, if possible, resolve the problem. If you are unable to solve the problem, contact a customer service representative for assistance and further instructions. Before you call, gather the following information:

Diagnostics

The power-on or hardware reset diagnostics provide full sets of test suites to test the LightStream  1010 ATM switch hardware. The test results are stored in the switch memory and an interface is provided using the show diag power-on command. If an error is detected during the test, the ASP status LED turns red. The watchdog timer timeout or software warm-start can run minimum diagnostics.

The following example shows the first few screens from the output of the show diag power-on command:

    Switch> show diag power-on

    LS1010 Power-on Diagnostics Status (.=Pass,F=Fail,U=Unknown,N=Not Applicable)

    -----------------------------------------------------------------------------

    Last Power-on Date: 97/04/14 Time: 16:03:22

    BOOTFLASH: . PCMCIA-Slot0: . PCMCIA-Slot1: N

    CPU-IDPROM: . FCard-IDPROM: . NVRAM-Config: .

    SRAM: . DRAM: .

    PS1: . PS2: N PS (12V): .

    FAN: . Temperature: . Bkp-IDPROM: F

    MMC-Switch Access: . Accordian Access: .

    LUT: . ITT: . OPT: . OTT: . STK: . LNK: . ATTR: . Queue: .

    Cell-Memory: .

    Feature-Card Access: .

    ICC: . OCC: . OQP: . OQE: . CC: . RT: .

    TM0: . TM1: . TMC: . IT: . LT: . RR: . ABR: .

    Access/Interrupt/Loopback/CPU-MCast/Port-MCast/FC-MCast/FC-TMCC Test Status:

    Ports 0 1 2 3

    ----------------------------------------------------------------------------

    PAM 0/0 (T1CE) ....... ....... ....... .......

    PAM 0/1 (155MM) ....... ....... ....... .......

    PAM 1/0 (155MM) ....... ....... ....... .......

    PAM 1/1 (155MM) ....... ....... ....... .......

    PAM 3/0 (155UTP) ....... ....... ....... .......

    PAM 3/1 (DS3Q) ....... ....... ....... .......

    PAM 4/0 (T1CE) ....... ....... ....... .......

    Ethernet-port Access: . Ethernet-port CAM-Access: .

    Ethernet-port Loopback: . Ethernet-port Loadgen: .

When the information about PAMs appears in the output, if a failure occurs, an "F" displays and a period (.) indicates the test passed.

Troubleshooting Flowchart

The flowchart in Figure 4-1 helps you determine which component of your LightStream  1010 ATM switch might have malfunctioned.


Figure 4-1: Troubleshooting Flowchart


Module LEDs

This section describes the LEDs used to confirm and troubleshoot operation of the ASP. The LEDs on the ASP indicate the status of the ASP, fan assembly, and power supplies. The ASP LEDs are shown in Figure 4-2 and described in Table 4-1.


Figure 4-2: ASP LEDs



Table 4-1: ASP LEDs
LED Color Description

Status

Green

The system has passed internal self-tests and diagnostic tests.

Red

The system has failed internal self-tests and diagnostic tests.

Orange

The system is booting or a module is disabled.

Fan

Green

The fan is operational.

Red

The fan is not operational.

PS 0, Left Bay

Green

The power supply is operational.

Red

The power supply is installed but not operational.

Off

The power supply is not installed.

PS 1, Right Bay

Green

The power supply is operational.

Red

The power supply is installed but not operational.

Off

The power supply is not installed.

Link

Green

The Ethernet port is operational.

Off

No signal is detected on the Ethernet port.

RX (Receive)

Flashing green

Ethernet packets are being received. The pulse rate increases with the data rate.

Off

No signal is being received.

TX (Transmit)

Flashing green

Ethernet packets are being transmitted. The pulse rate increases with the data rate.

Off

No signal is being transmitted.

Testing the Configuration

Table 4-2 describes some commands you can enter in privileged EXEC mode to verify that the hardware, software, and interfaces have been configured correctly.


Table 4-2: Initial Configuration Testing Commands
Command Description

show version

Displays the version and type of software installed.

show hardware

Displays the type and revision number of the hardware installed in the system.

show interface ethernet card/subcard/port

Displays the Ethernet configuration.

show atm address

Displays the ATM address.

ping atm interface atm

Tests for connectivity between the switch and a host.

show atm interface

Displays the configuration of the ATM interfaces. (Press Ctrl  z to stop the display messages.)

show atm status

Displays the status of the ATM interfaces.

show atm vc

Displays the status of the ATM virtual interfaces.

show running-config

Displays the configuration being used.

show startup-config

Displays the configuration saved in NVRAM.


hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1998 © Cisco Systems Inc.