Table A-1: System Specifications
| Description
| Specifications
|
|---|
Dimensions (H x W x D)
| CM: 1.2 x 14.4 x 16" (3.0 x 36.6 x 40.6 cm)
PAM: 1.2 x 6.5 x 10" (3.0 x 16.5 x 25.4 cm)
|
Weight
| CM: 3.55 lb (1.60 kg)
PAM (approximately): 1.10 lb (0.50 kg)
|
DC Voltages Supplied and Steady-state Maximum Current Ratings
| +5V @ 70A
+12V @ 2A
+24V @ 0.2A
|
Operating Temperature
| 32-104ºF (0-40ºC)
|
Nonoperating Temperature
| -40-167ºF (-40-75ºC)
|
Humidity
| 10-90%, noncondensing
|
Altitude
| -500 to 10,000 ft (-52 to 3,048 m)
|
Interface Timing
| Loop timing, Stratum 4 accuracy clock for self-timing; synchronous, SRTS, or adaptive clocking for CBR traffic
|
Carrier Module (CM)
| Carrier module for 2-port adapter modules with PAM slot covers for empty slots installed (product number WATM-CAM-2P=)
|
Port Adapter Modules (PAM)
| PAM with 4 SONET STS3c/SDH STM1 multimode fiber ports, SC connectors (WAI-OC3-4MM)
PAM with 4 SONET STS3c/SDH STM1 single-mode fiber ports, SC connectors
(WAI-OC3-4SM)
PAM with 4 SONET STS3c/SDH STM1, 1 single-mode fiber port, 3 multimode
fiber ports, SC connectors (WAI-OC3-1S3M)
PAM with 4 SONET STS3c/SDH STM1 UTP-5 ports, RJ-45 connectors
(WAI-C3-4U5)
PAM with 1SONET STS12c/SDH STM4c single-mode fiber ports, SC connector
(WAI-OC12-1SM)
PAM with 1SONET STS12c/SDH STM4c multimode fiber ports, SC connector
(WAI-OC12-1MM)
PAM with 2 DS-3 ports, BNC connectors (WAI-T3-2BNC)
PAM with 4 DS-3 ports, BNC connectors (WAI-T3-4BNC)
PAM with 2 E3 ports, BNC connectors (WAI-E3-2BNC)
PAM with 4 E3 ports, BNC connectors (WAI-E3-4BNC)
PAM with 12 25-Mbps ports, RJ-45 connectors (WAI-ATM25-12P)
PAM with 4 E1 trunk ports, RJ-48 connectors (WAI-E1-4RJ48)
PAM with 4 T1 trunk ports, RJ-48 connectors (WAI-T1-4RJ48)
PAM with 4 E1 trunk ports, BNC connectors (WAI-E1-4BNC)
PAM with 4 E1 CES ports, BNC connectors (WAI-E1C-4BNC)
PAM with 4 E1 CES ports, RJ-48 connectors (WAI-E1C-4RJ48)
PAM with 4 T1 CES ports, RJ-48 connectors (WAI-T1C-4RJ48)
|
Signaling and Routing
| UNI 3.0, UNI 3.1 in future release
ILMI
PNNI Phase 1, IISP
Soft PVC/PVP support
ATM access list and firewalls
Crankback
Plug-and-play mode with PNNI image
Redundant link support with load balancing or best-fit selection
|
Traffic Management
| Single, dual-mode leaky-bucket traffic policing
Per-port traffic pacing
Multiple configurations per connection, port, and switch threshold
Multiple priority classes
All ATM connection types and AALs
Connection Admission Control
CLP1 tagging and discard
Intelligent packet discard
Available bit rate support: EFCI2 marking mode and relative rate marking mode
|
Network Management
| Port TX and RX LEDs, switch and common equipment status LEDs
S1, S2, and CD LEDs (CES T1 and CES E1)
Port snooping and connection steering
Multiple standard and enterprise MIBs
Text-based command line interface based on familiar router interface
Standard Cisco IOS security capabilities: password and TACACS,3
Telnet, TFTP, BOOTP, LAN Emulation client, RFC 1577 Classical IP over
ATM client (for management access)
|
Management Information Bases (MIB)
| SNMP MIB II (RFC 1213)
Interface table MIB (RFC 1573)
AToMIC (RFC 1695)
ATM Forum PNNI MIB
ATM Forum UNI 30/3.1 ILMI MIB
|
Maximum
Station-to-station Cabling Distance
| DS-3---coaxial cable: 450 ft (137 m)
E3---coaxial cable: 450 ft (137 m)
OC-3---UTP cable: 328 ft (100 m)
OC-3 and 12---9/125-micron single-mode fiber: 9 miles (15 km)
OC-3 and 12---9/125-micron single-mode long-reach fiber:18 miles (30 km)
OC-3 ---50/125-micron and 62.5/125-micron multimode fiber: 1.24 miles (2 km)
OC-12---50/125-micron and 62.5/125-micron multimode fiber: 1,640 ft (500 m)
T1---UTP: 650 ft (198 m)
E1---UTP: 650 ft (198 m)
E1---coaxial cable: 650 ft (198 m)
T1 CES---twisted-pair and STP4: 820 ft (248.5 m) (5.5dB attenuation at
772 KHZ), 100-ohm, 24 AWG, UTP cable with RJ-48C connectors.
E1 CES---twisted-pair and STP: 820 ft (248.5 m) (5.5dB attenuation at
772 KHZ), 100-ohm, 24 AWG, UTP cable with RJ-48C connectors.
E1 CES---coaxial cable: 650 ft (198 m)
25-Mbps---UTP: 328 ft (100 m) with four or fewer separate cable segments on the path
|
Fiber-Optic Power Levels:
OC-3 Single-mode
Output Center Wavelength
Transmit
Receive
|
1261 to 1360 nm5
Minimum: -15.0 dBm
Maximum: -8.0 dBm
Minimum: -28.0 dBm
Maximum: -8.0 dBm
|
OC-3 Single-mode long-reach
Output Center Wavelength
Transmit
Receive
|
1281 to 1380 nm
Minimum: -5.0 dBm
Maximum: 0.0 dBm
Minimum: -34.0 dBm
Maximum: -10.0 dBm
|
OC-3 Multimode
Output Center Wavelength
Transmit
Receive
|
1270 to 1380 nm
Minimum: -20.0 dBm
Maximum: -14.0 dBm
Minimum: -30.0 dBm
Maximum: -14.0 dBm
|
Fiber-optic power levels: (cont.)
OC-12 Single-mode
extended reach
Output Center Wavelength
Transmit
Receive
OC-12 Multimode
Output Center Wavelength
Transmit
Receive
|
1274 to 1356 nm
Minimum: -15.0 dBm
Maximum: -8.0 dBm
Minimum: -28.0 dBm
Maximum: -8.0 dBm
1270 to 1380 nm
Minimum: -20.0 dBm
Maximum: -14.0 dBm
Minimum: -26.0 dBm
Maximum: -14.0 dBm
|
OC-12 Single-mode long-reach
Output Center Wavelength
Transmit
Receive
|
1280 to 1335 nm
Minimum: -3.0 dBm
Maximum: 2.0 dBm
Minimum: -28.0 dBm
Maximum: -8.0 dBm
|
Agency Approvals
| Safety: UL6 1950, CSA7-C22.2 No. 950, EN60950, IEC9508, TS001, AS/NZS 3260,
EMI9: FCC Part 15 Class A, Canadian ICES-003 Class A, CE Masking, EN55022 Class A, VCCI Class III, CISPR A with UTP, EN55022 Class B, CISPR Class B, VCCI Class II with shielded cables
|
