Table of Contents

cablelength
called-address-mask
called-nsap-address
calling-address-mask
calling-nsap-address
cast-type
ces aal1 clock
ces aal1 service
ces circuit
ces dsx1 clock source
ces dsx1 framing
ces dsx1 lbo
ces dsx1 linecode
ces dsx1 loopback
ces dsx1 signalmode robbedbit
ces pvc
channel-group
clear atm pnni
clear atm signalling statistics
clear atm-vc
clear-cause
clear counters
clear dialer
clear facility-alarm (Catalyst 8540 MSR)
clear host
clear interface
clear ip accounting
clear ip redirect
clear lane client
clear lane le-arp
clear lane server
clear rif-cache
clear sgcp statistics
client-atm-address name
clock source (controller)
clock source (interface) (Catalyst 8510 MSR and LightStream 1010)
clock source (Catalyst 8540 MSR)
collection-modes
configure
connection-category
connection-types
controller
copy
copy flash
copy rcp
copy running-config
copy startup-config
copy tftp
custom-queue-list

C Commands

The commands shown in this chapter apply to the Catalyst 8540 MSR, Catalyst 8510 MSR, and LightStream 1010. Where an entire command or certain attributes of a command have values specific to a particular switch, an exception is indicated by the following callouts:

• Catalyst 8540 MSR

• Catalyst 8510 MSR and LightStream 1010

cablelength

To configure the cable length for a channelized DS-3 (CDS3) Frame Relay port adapter, use the cablelength controller configuration command. To restore the default cable length, use the no form of this command.

Syntax Description

Default

224 feet

Command Mode

Controller configuration

Usage Guidelines

Although you can specify a cable length from 0 to 450 feet, the hardware only recognizes two ranges: 0 to 224, and 225 to 450.

For example, if you enter 150 feet, the 0 to 224 range is used. If you later change the cable length to 200 feet, there is no change because 200 is within the 0 to 224 range. However, if you change the cable length to 250, the 225 to 450 range is used. The actual number you enter is stored in the configuration file.

Example

The following example configures the cable length on controller t3 to 450 feet.

Switch(config)# controller t3 4/0/0
Switch(config-controller)# cablelength 450
Switch# show running-config
controller T3 4/0/0
 clock source reference
 cablelength 450

called-address-mask

To configure the address mask for identifying valid bits of the called NSAP address field, use the called-address-mask ATM signalling diagnostics configuration command. To return the address mask to the default, use the no form of this command.

Syntax Description

Default

NULL

Command Mode

ATM signalling diagnostics configuration

Usage Guidelines

To match this selection criteria, a failed connect setup must have a called party address value equal to the configured called party address for all bits that are 1 in the value of the mask specified with the command. When the default value is retained, the rejected call matches the filter criteria for any called address in the rejected call.

Example

The following example shows configuring a called address mask string.

Switch# configure terminal
Switch(config)# controller atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# called-address-mask ff.ff.ff

called-nsap-address

To configure the NSAP-format ATM address for the signalling diagnostics filter entry, use the called-nsap-address ATM signalling diagnostics configuration command. To remove any configured address, use the no form of this command.

Syntax Description

Default

NULL

Command Mode

ATM signalling diagnostics configuration

Usage Guidelines

NSAP-format ATM end-system addresses have a fixed length of 40 hexadecimal digits. You should configure the address using the following dotted format:

xx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xx

Example

The following example shows setting a called NSAP address.

Switch# configure terminal
Switch(config)# controller atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# called-nsap-address 47.111122223333444455556666.777788881111.00

calling-address-mask

To configure the address mask for identifying valid bits of the calling-nsap-address field in the signalling diagnostics filter table entry, use the calling-address-mask ATM signalling diagnostics configuration command. To set to the default value, use the no form of this command.

Syntax Description

Default

NULL

Command Mode

ATM signalling diagnostics configuration

Usage Guidelines

To match this selection criteria, a failed connect setup must have a calling party address value equal to the configured calling party address for all bits that are 1 in the value of the mask specified through the command. When the default value is retained, the rejected call matches the filter criteria for any calling address in the rejected call.

Example

The following example shows a calling address mask.

Switch# configure terminal
Switch(config)# controller atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# calling-address-mask ff.ff.ff

calling-nsap-address

To configure the NSAP-format ATM address for the signalling diagnostics filter entry, use the calling-nsap-address ATM signalling diagnostics configuration command. To remove any configured address, use the no form of this command.

Syntax Description

Default

NULL

Command Mode

ATM signalling diagnostics configuration

Usage Guidelines

NSAP-format ATM end-system addresses have a fixed length of 40 hexadecimal digits. You should configure the address using the following dotted format:

xx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xxxx.xx

Example

The following example shows setting a calling NSAP address.

Switch# configure terminal
Switch(config)# controller atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# calling-nsap-address 47.111122223333444455556666.777788881111.00

cast-type

To filter ATM signalling call failures by connection type (point-to-point or point-to-multipoint), use the cast-type ATM signalling diagnostics configuration command. To disable this feature, use the no form of this command.

Syntax Description

Default

All

Command Mode

ATM signalling diagnostics configuration

Example

The following example shows call failures filtered by point-to-point connection.

Switch# configure terminal
Switch(config)# controller atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# cast-type p2p

ces aal1 clock

To configure the AAL1 timing recovery clock for T1/E1 interfaces, use the ces aal1 clock interface configuration command. To revert to the default setting, use the no form of this command.

Syntax Description

Default

Synchronous

Command Mode

Interface configuration

Usage Guidelines

The clock mode must be synchronous for structured mode. In unstructured mode, use adaptive when a network-derived clock is not available.

Use srts when a network-derived clock is available but devices attached to the CES port use a different clock reference. The srts keyword samples the incoming clock, subtracts from the network clock, and sends the remainder in an AAL1 header. The clock is reconstructed during output by adding the residual to the network reference.

Use synchronous for all other modes.

Example

The following command shows setting the AAL1 timing recovery clock to adaptive mode.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces aal1 clock adaptive

ces aal1 service

To configure the type of ces service, use the ces aal1 service interface configuration command. To revert to the default setting, use the no form of this command.

Syntax Description

Default

Unstructured

Command Mode

Interface configuration

Usage Guidelines

The structured keyword means that each time slot is an independent entity grouped into circuits, where each circuit has an independent PVC.

The unstructured keyword reduces the incoming serial data on the receiving end of the ATM network. The keyword also sets the service to single circuit, single PVC, where all time slots are carried.

Example

The following example shows changing the mode for the ces aal1 service command to structured.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces aal1 service structured

ces circuit

To configure the CES connection attributes, use the ces circuit interface command. To revert to the default setting, use the no form of this command.

Syntax Description

Default

See "Syntax Description."

Command Mode

Interface configuration

Usage Guidelines

Channel-associated signalling provides information about the time slot (on or off the hook) and is updated once per multiframe.

Example

The following example shows setting the structured service CDV range to 5000 milliseconds.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces circuit 3 cdv 5000

ces dsx1 clock source

To configure a transmit clock source to the T1/E1 CES port adapter, use the ces dsx1 clock source interface configuration command. To revert to the default value, use the no form of this command.

Syntax Description

Default

network-derived

Command Mode

Interface configuration mode

Example

The following example shows setting the clock source to loop-timed.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces dsx1 clock source loop-timed

Related Command

ces aal1 clock

ces dsx1 framing

To select the frame type for the E1 or T1 data line, use the ces dsx1 framing interface configuration command. To revert to the default setting, use the no form of this command.

To restore the default setting, use the no form of these commands.

Syntax Description

Default

The default for E1 is el_lt. The default for T1 is esf.

Command Mode

Interface configuration

Usage Guidelines

Use this command in configurations where the switch communicates with either the T1 or the E1 data line to configure the frame type for your circuit.

Example

The following example shows setting the E1 data line frame type to e1_mfCAS_lt.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces dsx1 framing e1_mfCAS_lt

Related Command

linecode

ces dsx1 lbo

To configure T1 port parameters, use the ces dsx1 lbo interface configuration command. To revert to the default setting, use the no form of this command.

Syntax Description

Default

0-110

Command Mode

Interface configuration

Usage Guidelines

Set the cable length to the desired number of feet on your system.

Example

The following example shows setting the cable length to 440 feet using the ces dsx1 lbo interface configuration command.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces dsx1 lbo 440_550

ces dsx1 linecode

To select the linecode type for the T1 or E1 line, use the ces dsx1 linecode interface configuration command. To revert to the default setting, use the no form of this command.

Syntax Description

Default

For T1: b8zs.

For E1: hdb3.

Command Mode

Interface configuration

Usage Guidelines

The T1 service provider determines which linecode type, either ami or b8zs, is required for your circuit. The E1 service provider determines which linecode type, either ami or hdb3, is required for your circuit.

Example

The following example specifies b8zs as the linecode type for the T1 interface.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces dsx1 linecode b8zs

ces dsx1 loopback

To configure loopback for the T1 or E1 circuit emulation port adapter module, use the ces dsx1 loopback interface configuration command. To revert to the default setting, use the no for of this command.

Syntax Description

Default

noloop

Command Mode

Interface configuration

Usage Guidelines

This command is useful when testing the circuit emulation port adapter module.

Example

The following example shows setting the loopback to payload.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces dsx1 loopback payload

ces dsx1 signalmode robbedbit

To configure the signalmode to robbedbit, use the ces dsx1 signalmode robbedbit interface configuration command. To revert to the default setting, use the no form of this command.

Syntax Description

This command has no keywords or arguments.

Default

no

Command Mode

Interface configuration

Usage Guidelines

A T1 frame consists of 24 time slots (DS0) that send at a rate of 64 kbps. T1 defines the ability to send signalling in-band on individual time slots by removing the low bit of each byte for signalling in robbedbit mode. This procedure allows 8 kbps for signalling and leaves 56 kbps for data.

In structured mode, you can send the T1 signalling information across the BISDN network. This means that after you set the port in robbedbit signalling mode, and enable CAS on individual circuits that need this type of service, you are robbing bits from the DS0. The system then puts the bits in the specified format to be sent across the BISDN network and reinserts them at the passive side on the CES-IWF connection.

Example

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces dsx1 signalmode robbedbit

Related Commands

ces aal1 service
ces circuit

ces pvc

To configure the destination port for the circuit, use the ces pvc interface configuration command. To disable this feature, use the no form of this command.

Syntax Description

Command Mode

Interface configuration

Usage Guidelines

Use the interface option to create a hard PVC. Use the dest-address option to create a soft PVC.

You must configure both sides of the CES circuits because the source (the active side in CES-IWF) time slots are not recognized at the destination (the passive side).

Each CES circuit has an ATM address. When configuring the source PVC, you need the destination ATM address. See the show ces address command.

Examples

The following example shows setting a hard PVC on interface ATM 1/0/0.

Switch# configure terminal
Switch(config)# controller cbr 3/0/0
Switch(config-if)# ces pvc 31 interface atm 1/0/0
 

The following example shows setting an unstructured CES soft PVC.

Switch(config-if)# ces pvc 0 dest-atm-addr atm 1/0/0 vpi 1 vci 1
 

The following example shows setting a structured hard PVC.

Switch(config-if)# ces pvc 24 interface atm 1/0/1 vpi 1 vci 1

Related Command

show ces address

channel-group

To form a serial interface, or channel-group, by aggregating time slots on a channelized DS3 (CDS3) or channelized E1 (CE1) line, use the channel-group controller configuration command. To delete a serial interface or channel-group, use the no form of this command.

For the CDS3 Frame Relay line, use the following syntax:

For the CE1 Frame Relay line, use the following syntax:

Syntax Description

Default

64 Kbps for CDS3.

Not applicable to CE1.

Command Mode

Controller configuration

Usage Guidelines

If the serial interface has encapsulation set to Frame Relay, then the no form of this command works only if you shut down the interface or the controller so that it tears down all soft VCs automatically. Otherwise, an error is returned.

Example

The following example shows how to configure a channel group (#2), assigning time slots 6 to 31, and creating a logical serial port on interface 1/0/0:2.

Switch(config)# controller e1 1/0/0
Switch(config-control)# channel-group 2 timeslots 6-31
 

clear atm pnni

To clear PNNI-related data, use the clear atm pnni privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Example

The following example shows how to clear the PNNI flooding statistics.

Switch# clear atm pnni statistics flooding

Related Commands

atm pnni node
show atm pnni local-node

clear atm signalling statistics

To clear existing ATM signalling statistics, use the clear atm signalling statistics EXEC command.

Syntax Description

Command Mode

EXEC

Usage Guidelines

This command clears the statistics for all the interfaces or a specific interface.

Example

The following example shows how to clear the ATM signalling statistics for interface 1/0/0.

Switch# clear atm signalling statistics interface atm 1/0/0

Related Command

show atm signalling statistics

clear atm-vc

To release a specified SVC, use the clear atm vc privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Example

The following is an example of the clear atm-vc command, which releases interface 3/1/0 on VPI 0 and VCI 99.

Switch# clear atm-vc atm 3/1/0 0 99

Related Command

show atm vc

clear-cause

To configure the release cause code value in the signalling diagnostics filter table entry, use the clear-cause ATM signalling diagnostics configuration command. To disable this feature, use the no format of this command.

Syntax Description

Default

0

Command Mode

ATM signalling diagnostics configuration

Usage Guidelines

Only the call failure records that match this configured clear-cause value are collected and stored. The default value zero (0) means the cause code is not considered during filtering.

Example

The following example shows setting a value of 100.

Switch(cfg-atmsig-diag)# clear-cause 100

clear counters

It is recommended that you only use this command for debugging purposes because it clears all counters displayed in the show interface and show controllers commands. To clear the interface counters, use the clear counters privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Usage Guidelines

This command clears all the current interface counters from the interface unless the optional arguments type and card/subcard/port are specified to clear only a specific interface type (ATM, Ethernet, and so on).

Example

The following example illustrates how to clear all interface counters.

Switch# clear counters

Related Command

show ip access-lists

clear dialer

clear facility-alarm (Catalyst 8540 MSR)

Use the clear facility-alarm command to clear alarm conditions and reset the alarm contacts.

Syntax Description

Default

Clears all facility alarms.

Command Mode

Privileged EXEC

Usage Guidelines

The clear facility-alarm command acts like an ACO. Only a reoccurrence of the original alarm source after the original alarm condition is removed can restart the alarm.

Examples

The following example shows how to clear minor facility alarms only.

Switch# clear facility-alarm minor
Clearing minor alarms
Switch# 
 

The following example shows how to clear all facility alarms.

Switch# clear facility-alarm
Clearing all alarms
Switch# 

Related Commands

facility-alarm (Catalyst 8540 MSR)
show facility-alarm status (Catalyst 8540 MSR)

clear host

To delete entries from the host-name-and-address cache, use the clear host privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Usage Guidelines

The host name entries are cleared in running memory.

Example

The following example clears all entries from the host-name-and-address cache.

Switch# clear host *

Related Command

show hosts

clear interface

To reset the hardware logic on an interface, use the clear interface privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Usage Guidelines

Under normal circumstances, you do not need to clear the hardware logic on interfaces.

Example

The following example resets the interface logic on ATM interface 1/0/1.

Switch# clear interface ATM 1/0/1

clear ip accounting

To delete the cache table entries, use the clear ip cache privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Related Command

show ip interface

clear ip redirect

To redirect an IP cache, use the clear ip redirect privileged EXEC command.

Syntax Description

This command has no keywords or arguments.

Command Mode

Privileged EXEC

Related Command

show ip redirects

clear lane client

To clear the LANE client counter configured on the specified LEC interface, use the
clear lane client privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Usage Guidelines

If you do not specify an interface, this command clears all the counters of any LANE client in the switch.

When you specify an interface, this command clears all the LANE client counters on that interface.

Example

The following example shows clearing the counters on ATM 1/0/0 interface using the
clear lane client privileged EXEC command.

Switch# clear lane client join-cnt interface atm 1/0/0

Related Commands

lane database
show lane client

clear lane le-arp

To clear the dynamic LE_ARP table or a single LE_ARP entry of the LANE client configured on the specified subinterface or emulated LAN, use the clear lane le-arp privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Usage Guidelines

This command only removes dynamic LE_ARP table entries. It does not remove static LE_ARP table entries.

If you do not specify an interface or an emulated LAN, this command clears all the LANE ARP tables of any LANE client in the switch.

If you specify a major interface (not a subinterface), this command clears all the LANE ARP tables of every LANE client on all the subinterfaces of that interface.

This command also removes the fast-cache entries built from the LANE ARP entries.

Examples

The following example clears all the LANE ARP tables for all clients on the switch.

Switch# clear lane le-arp
 

The following example clears all the LANE ARP tables for all LANE clients on all the subinterfaces of interface atm 0.

Switch# clear lane le-arp interface atm 0
 

The following example clears the entry corresponding to MAC address 0800.AA00.0101 from the LE_ARP table for the LANE client on the emulated LAN named red.

Switch# clear lane le-arp name red 0800.aa00.0101
 

The following example clears all dynamic entries from the LE_ARP table for the LANE client on the emulated LAN named red.

Switch# clear lane le-arp name red 
 

The following example clears the dynamic entry from the LE_ARP table for the LANE client with next-hop router descriptor segment number 1, bridge number 1, on the emulated LAN named red.

Switch# clear lane le-arp name red route-desc segment 1 bridge 1

clear lane server

To force a LANE server on a specified subinterface or emulated LAN to drop the Control Direct and Control Distribute VCCs to a given LANE client and force the client to rejoin, subject to the new bindings, use the clear lane server privileged EXEC command.

Syntax Description

Command Mode

Privileged EXEC

Usage Guidelines

After changing the bindings on the configuration server, enter this command on the LANE server. The LANE server drops the Control Direct and Control Distribute VCCs to the LANE client. The client then asks the LANE configuration server for the location of the LANE server of the emulated LAN it is requesting to join.

If no LANE client is specified, all LANE clients attached to the LANE server are dropped.

Example

The following example forces all the LANE clients on the emulated LAN named red to be dropped. When they try to join again, they are forced to join a different emulated LAN.

Switch# clear lane server red

Related Commands

lane database
show lane server

clear rif-cache

To clear the RIF cache, use the clear rif-cache privileged EXEC command.

Syntax Description

This command has no keywords or arguments.

Command Mode

Privileged EXEC

Usage Guidelines

Some entries in the RIF cache are dynamically added, while others are static.

Related Commands

rif
rif timeout
show rif

clear sgcp statistics

To clear all SGCP statistics, use the clear sgcp statistics privileged EXEC command.

Syntax Description

This command has no arguments or keywords.

Default

None

Command Mode

Privileged EXEC

Usage Guidelines

This command clears global and per-endpoint statistics.

Example

The following example clears the SGCP statistics.

Switch# clear sgcp statistics

Related Commands

show sgcp
show sgcp endpoint

client-atm-address name

To add a LANE client address entry to the configuration servers configuration database, use the client-atm-address name lane configuration server database command. To remove a client address entry from the table, use the no form of this command.

Syntax Description

Default

No address and no emulated LAN name are provided.

Command Mode

LANE configuration server database

Usage Guidelines

This command binds any client whose address matches the specified template into the specified emulated LAN. When a client comes up, it consults the LANE configuration server, which responds with the ATM address of the LANE server for the emulated LAN. The client then initiates join procedures with the LANE server.

Before this command is used, the emulated LAN specified by the elan-name argument must be created in the configuration server's database by using the name server-atm-address command.

If an existing entry in the configuration server's database binds the LANE client ATM address to a different emulated LAN, the new command is rejected.

This command affects only the bindings in the named configuration server database. It has no effect on the LANE components themselves.

The client-atm-address name command is a subcommand of the global lane database command. See the lane database command for information about creating the database, and the name server-atm-address command for information about binding the emulated LAN name to the servers ATM address.

ATM Addresses. A LANE ATM address has the same syntax as an NSAP but it is not a network-level address. It consists of the following:

• A 13-byte prefix that includes the following fields defined by the ATM Forum:

AFI field (1 byte), DCC or ICD field (2 bytes), DFI field (1 byte), Administrative Authority field (3 bytes), Reserved field (2 bytes), Routing Domain field (2 bytes), and the Area field (2 bytes)

• A 6-byte ESI

• A 1-byte selector field

Address Templates. LANE ATM address templates can use two types of wildcards: an asterisk (*) to match any single character (nibble), and an ellipsis (...) to match any number of leading, middle, or trailing characters. The values of the characters replaced by wildcards come from the automatically assigned ATM address.

In LANE, a prefix template explicitly matches the prefix, but uses wildcards for the ESI and selector fields. An ESI template explicitly matches the ESI field, but uses wildcards for the prefix and selector.

With the Cisco implementation of LANE, the prefix corresponds to the switch, the ESI corresponds to the ATM interface, and the selector field corresponds to the specific subinterface of the interface.

Examples

The following example shows how to enter database configuration mode using the database lane_db.

Switch(config)# lane database lane_db
Switch(lane-config-database)#
 

The following example uses an ESI template to specify the part of the ATM address corresponding to the interface. This example allows any client on any subinterface of the interface that corresponds to the displayed ESI value, no matter where the switch is connected, to join the engineering emulated LAN.

Switch(lane-config-database)# client-atm-address ...0800.200C.1001.** name engineering
 

The following example uses a prefix template to specify the part of the ATM address corresponding to the switch. This example allows any client on a subinterface of any interface connected to the switch that corresponds to the displayed prefix to join the marketing emulated LAN.

Switch(lane-config-database)# client-atm-address 47.000014155551212f.00.00... name marketing

Related Commands

delay
lane database
name server-atm-address

clock source (controller)

To select a transmit clock source for a channelized DS3 (CDS3) or a channelized E1 (CE1) Frame Relay port adapter, or for a 16-port OC-3c MMF port adapter, use the clock source controller configuration command. To return the clock source to the default, use the no form of this command.

Syntax Description

Default

For CDS3 and CE1 Frame Relay port adapters, the default clock source is loop-timed.

For the OC-3c MMF port adapter, the default clock source is network-derived.

Command Mode

Controller configuration

Usage Guidelines

Currently, all types of OC-12 port adapters do not support loop-timed mode.

When a transmit clock port is set to free-running, if there is a local oscillator present on the port adapter, the port uses the port adapter's oscillator as the clock source. If there is no local oscillator present on the port adapter, the port uses the route processor oscillator.

Example

The following example shows how to enable the reference clocking mode on an E1 interface.

Switch# configure terminal
Switch(config)# controller e1 1/0/0 
Switch(config-controller)# clock source reference

Related Commands

network-clock-select
show controllers

clock source (interface) (Catalyst 8510 MSR and LightStream 1010)

To select a transmit clock source for a physical device such as a port, use the clock source interface configuration command. To return the clock source to the default, use the no form of this command.

Syntax Description

Default

loop-timed

Command Mode

Interface configuration

Usage Guidelines

This command applies to all interfaces except older versions of the DS3/E3 and the 25-Mbps interfaces.

This subcommand allows selection of the transmit clock source for the physical device of a port. Currently, all types of OC-12 port adapters do not support loop-timed mode.

When a transmit clock port is set to free-running, if there is a local oscillator present on the port adapter, the port uses the port adapter's oscillator as the clock source. If there is no local oscillator present on the port adapter, the port uses the route processor oscillator.

Example

The following example shows how to enable the loop-timed clocking mode.

Switch(config-if)# clock source loop-timed

Related Commands

framing (interface configuration)
network-clock-select

clock source (Catalyst 8540 MSR)

To select a transmit clock source for a physical device such as a port, use the clock source interface configuration command. To return the clock source to the default, use the no form of this command.

Syntax Description

Default

loop-timed

Command Mode

Interface configuration

Usage Guidelines

This command applies to all interfaces except older versions of the DS3/E3 and the 25-Mbps interfaces.

This subcommand allows selection of the transmit clock source for the physical device of a port. Currently, all types of OC-12 port adapters do not support loop-timed mode.

When a transmit clock port is set to free-running, if there is a local oscillator present on the port adapter, the port uses the port adapter's oscillator as the clock source. If there is no local oscillator present on the port adapter, the port uses the route processor oscillator.

Example

The following example shows how to enable the loop-timed clocking mode.

Switch(config-if)# clock source loop-timed

Related Commands

framing (interface configuration)
network-clock-select

collection-modes

To initialize the collection mode and specify at what time accounting data is recorded in the accounting file, use the collection-modes ATM accounting file subcommand. To disable the collection mode, use the no form of this command.

Syntax Description

Command Mode

ATM accounting file

Example

The following example initializes the collection mode and specifies that the accounting data is recorded on the release of a connection.

Switch# configure terminal
Switch(config)# atm accounting file acctng_file1
Switch(config-acct-file)# collection-modes on-release

Related Commands

atm accounting file
failed-attempts
min-age

configure

To enter global configuration mode, use the configure privileged EXEC command. You must be in global configuration mode to enter global configuration commands.

Syntax Description

Default

No default

Command Mode

Privileged EXEC

Usage Guidelines

If you do not specify terminal or memory, the switch prompts you for the source of configuration commands. If you specify terminal, the switch executes the commands you enter at the system prompts.

If you specify memory, the switch executes the commands pointed to by the config_file environment variable. The config_file environment variable specifies the device and filename of the configuration file that the switch uses to configure itself during initialization. Possible devices are as follows:

• bootflash: This device is the internal Flash memory and is the initial default device.

• slot0: This device is the first PC slot on the route processor card and is the initial default device.

• slot1: This device is the second PC slot on the route processor card.

To view the contents of the config_file environment variable, use the show bootflash: command. To modify the config_file environment variable, use the boot config command and then save your changes by issuing the copy running-config startup-config command.

After you enter the configure command, the system prompt changes from switch-name# to switch-name(config)#, indicating that you are in global configuration mode. To leave global configuration mode and return to the privileged EXEC prompt, press ^Z.

Switch# show hosts 
 

To display the status of all TCP connections, enter the following command.

Switch# show tcp 
 

Examples

In the following example, the switch is configured from the terminal.

Switch# configure terminal
Switch(config)# 
 

In the following example, a switch runs the commands pointed to by the config_file environment variable.

Switch# configure memory

Related Commands

boot config
copy running-config
show bootflash:
show running-config
show startup-config

connection-category

To filter ATM signalling call failures by virtual circuit category, use the connection-category ATM signalling diagnostics configuration command. To return the connection category to the default, use the no form of this command.

Syntax Description

Default

all

Command Mode

ATM signalling diagnostics configuration

Usage Guidelines

Use the atm signalling diagnostics command to enter diagnostics configuration mode.

Example

In the following example, call failures are filtered by soft virtual circuits.

Switch# configure terminal
Switch(config)# controller atm 0/0/0
Switch(config-if)# atm signalling diagnostics 1
Switch(cfg-atmsig-diag)# connection-category soft-vc

connection-types

To set types of connections for atm accounting selection, use the connection-types ATM accounting selection command. To return the connection-type to the default, use the no form of this command.

Syntax Description

Default

The default value for the connection type is svc-in, svc-out, and svp-out.

Command Mode

ATM accounting selection

Usage Guidelines

Changes to connection-types take effect immediately.

Example

The following example shows specifying the connection types for ATM accounting selection index 1 as spvc-originator and spvp-originator.

Switch(config)# atm accounting selection 1
Switch(config-acct-sel)# connection-types spvc-originator spvp-originator

Related Commands

atm accounting selection
atm accounting collection
atm accounting file
list

controller

To select a port on a Frame Relay port adapter, use the controller global configuration command.

controller {t3 | e1} card/subcard/port

Syntax Description

Command Mode

Global configuration

Usage Guidelines

Specify the controller to configure by entering the controller subcommand, followed by e1 or t3, and card/subcard/port.

Example

The following example begins configuration of the CE1 Frame Relay interface on card 11, subcard 0, and port 0 using the controller global configuration command.

Switch# configure terminal
Switch(config)# controller e1 11/0/0

Related Commands

show controllers
show interface

copy

To copy any file from a Flash device to another destination, use the copy privileged EXEC command.

Syntax Description

Default

If you omit the source or destination device, the switch uses the default device specified by
the cd command. If you omit the destination filename, the switch uses the source filename.

Command Mode

Privileged EXEC

Usage Guidelines

The copy commands generally copy a file from a source to a destination. Some invalid combinations exist. Specifically, you cannot copy a running configuration to a running configuration, a startup configuration to a startup configuration, or TFTP to rcp.

When the destination is specified by the config_file or BOOTLDR environment variable, the switch prompts you for confirmation before proceeding with the copy. When the destination is the only valid image in the BOOT environment variable, the switch also prompts you for confirmation before proceeding with the copy.

The config_file environment variable specifies the configuration used during switch initialization. The BOOTLDR environment variable specifies the Flash device and filename containing the rxboot image for booting. The BOOT environment variable specifies a list of bootable images on various devices. To view the contents of environment variables, use the show bootflash: command.
To modify the config_file environment variable, use the boot config command. To modify the BOOTLDR environment variable, use the boot bootldr command. To modify the BOOT environment variable, use the boot system command. To save your modifications, use the copy running-config startup-config command.

If you do not specify a source or destination device, the switch uses the default device specified by the cd command.

Examples

The following example copies the switch-config1 file from the internal Flash memory of a switch to the switch-backupconfg file on the Flash memory card inserted in the first slot of the route processor card.

Switch# copy bootflash:switch-config1 slot0:switch-backupconfig
 

In the following example, the switch copies the switch-config file from the Flash memory card inserted in slot 0 of the route processor card to the startup configuration.

Switch# copy slot0:switch-config startup-config

Related Commands

boot config
copy flash
copy rcp
copy running-config
copy startup-config
copy tftp
dialer-list list

copy flash

To copy a file from Flash memory to another destination, use the copy flash privileged EXEC command.

Syntax Description

Default

If you omit the destination device, the switch uses the default device specified by the cd command. If you omit the destination filename, the switch uses the source filename.

Command Mode

Privileged EXEC

Usage Guidelines

The copy flash command copies from one of the three Flash memory devices. The system prompts you to enter a specific device and filename. You can enter one of the following as the source device:

• bootflash: This device is the internal Flash memory in the switch.

• slot0: This device is the first PC slot on the route processor card.

• slot1: This device is the second PC slot on the route processor card.

You must follow the source device with a colon (:) and a filename.

Use the copy flash rcp command to copy a system image from Flash memory to a network server using rcp. You can use the copy of the system image as a backup copy. You can also use it to verify that the copy in Flash memory is the same as the original file.

The rcp software requires that a client send the remote username on each rcp request to the server. When you issue the copy flash rcp command, by default the switch software sends the remote username associated with the current TTY if that name is valid. For example, if the user is connected to the switch through Telnet and was authenticated through the username command, the switch software sends that username as the remote username.

If the TTY username is invalid, the switch software uses the switch host name as both the remote and local usernames.

To specify a different remote username to be sent to the server, use the ip rcmd remote-username command. You can also specify the path of an existing directory along with the remote username.

Caution The remote username must be associated with an account on the destination server. If you do not use the ip rcmd remote-username command to specify the name of a remote user associated with an account on the server, the remote username associated with the current TTY process must be associated with an account on the server. If there is no username for the current TTY process, the switch host name must be associated with an account on the server. If the network administrator of the destination server did not establish accounts for the remote username used, this command does not execute successfully when a default remote username is used.

If you copy the system image to a personal computer used as a file server, the computer must support the rsh protocol.

Use the copy flash tftp command to copy a system image from Flash memory to a TFTP server. As with the copy flash rcp command, you can use the copy of the system image as a backup or to verify that the copy in Flash is the same as the original file.

The copy commands generally copy a file from a source to a destination. Some invalid combinations exist. Specifically, you cannot copy a running configuration to a running configuration, a startup configuration to a startup configuration, or TFTP to rcp. If you do not specify a source or destination device, the switch uses the default device specified by the cd command.

When the destination is also specified by the config_file environment variable, the switch prompts you for confirmation before proceeding with the copy. The config_file environment variable specifies the configuration used during switch initialization. To view the contents of the config_file environment variable, use the show bootflash: command. To modify the config_file environment variable, use the boot config command. To save your modifications to the config_file environment variable, use the copy running-config startup-config command.

Examples

The following example shows how to use the copy flash rcp command.

Switch# configure terminal
Switch# ip rcmd remote-username netadmin1
Ctrl-Z
Switch# copy flash rcp
 
System flash directory, partition 2:
File  Length   Name/status
  1   984      junk
[1048 bytes used, 8387560 available, 8388608 total]
Address or name of remote host [223.255.254.254]?
Source file name? junk
Destination file name [junk]? junk
Verifying checksum for 'junk' (file # 1)...  OK
Copy 'junk' from Flash to server
  as 'junk'? [yes/no]y
-
Upload to server done
Flash copy took 0:00:00 [hh:mm:ss]
 

You see a spinning line during the copy process.

The following example illustrates how to use the copy flash rcp command when copying from a particular partition of Flash memory.

Switch# copy flash rcp
System flash partition information:
Partition   Size     Used    Free    Bank-Size   State       Copy-Mode
1       4096K    2048K   2048K   2048K       Read Only   RXBOOT-FLH
2       4096K    2048K   2048K   2048K       Read/Write  Direct
 
[ Type ?number for partition directory; ? for full directory; q to abort]
Which partition? [default = 1]
 

The system prompts you if there are two or more partitions. If the partition entered is not valid, the process terminates. You have the option to enter a partition number, a question mark (?) for a directory display of all partitions, or a question mark and a number (?number) for a directory display of a particular partition. The default is the first partition.

System flash directory, partition 2:
File  Length   Name/status
1   3459720  master/igs-bfpx.100-4.3
[3459784 bytes used, 734520 available, 4194304 total]
Address or name of remote host [ABC.CISCO.COM]?
Source file name? 
 

The file is copied from the partition given earlier by the user.

Destination file name [default = source name]?
Verifying checksum for 'master/igs-bfpx.100-4.3' (file # 1)...  OK
Copy 'master/igs-bfpx.100-4.3' from Flash to server
as 'master/igs-bfpx.100-4.3'? [yes/no] yes
 

The following is sample output from the copy flash tftp command.

Switch# copy flash tftp:
Enter source file name: bootflash:test-image 
Enter destination file name [test-image]: tftpboot/backup-image
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Address or name of remote host []? 172.20.46.50
!
 

The following example illustrates how to use the copy flash tftp command when copying from a particular partition of Flash memory.

Switch# copy flash tftp
System flash partition information:
Partition   Size     Used    Free    Bank-Size   State       Copy-Mode
1       4096K    2048K   2048K   2048K       Read Only   RXBOOT-FLH
2       4096K    2048K   2048K   2048K       Read/Write  Direct
 
[Type ?number for partition directory; ? for full directory; q to abort]
Which partition? [default = 1]
 

The system prompts you if there are two or more partitions. If the partition entered is not valid, the process terminates. You have the option to enter a partition number, a question mark (?) for a directory display of all partitions, or a question mark and a number (?number) for a directory display of a particular partition. The default is the first partition.

System flash directory, partition 2:
File  Length   Name/status
1   3459720  master/igs-bfpx.100-4.3
[3459784 bytes used, 734520 available, 4194304 total]
Address or name of remote host [ABC.CISCO.COM]?
Source file name? 
 

The file is copied from the partition given earlier by the user.

Destination file name [default = source name]?
Verifying checksum for 'master/igs-bfpx.100-4.3' (file # 1)...  OK
Copy 'master/igs-bfpx.100-4.3' from Flash to server
as 'master/igs-bfpx.100-4.3'? [yes/no] yes
 

The following example shows how to use the copy flash command.

Switch# copy flash slot0:new-config

Related Commands

boot config
boot system flash
config-register
copy running-config startup-config
ip rcmd remote-username
show bootflash:

copy rcp

To copy a file from a network server to the switch or to another destination using rcp, use the
copy rcp privileged EXEC command.

Syntax Description

Default

If you omit the destination device, the switch uses the default device specified by the cd command. If you omit the destination filename, the switch uses the source filename.

Command Mode

Privileged EXEC

Usage Guidelines

The rcp protocol requires that a client send the remote username of an rcp request to the server. When you issue one of the copy rcp commands, by default the switch software sends the username associated with the current TTY if that name is valid. For example, if the user is connected to the switch through Telnet and the user was authenticated through the username command, the switch software sends that username as the remote username.

If the TTY username is invalid, the switch software uses the switch host name as both the remote and local usernames. To specify a different remote username to be sent to the rcp server, use the
ip rcmd remote-username command. You can also specify the path of an existing directory along with the remote username.

Caution The remote username must be associated with an account on the destination server. If you do not use the ip rcmd remote-username command to specify the name of a remote user associated with an account on the server, the remote username associated with the current TTY process must be associated with an account on the server. If there is no username for the current TTY process, the switch host name must be associated with an account on the server. If the network administrator of the destination server did not establish accounts for the remote username used, this command does not execute successfully when a default remote username is used.

If you copy a bootstrap image, system image, or configuration file from a personal computer used as a file server, the remote host computer must support the rsh protocol.

Use the copy rcp bootflash command to copy a bootstrap image from a network server to Flash memory using rcp. The switch prompts for the name or address of the server and the name of the file to be copied. It provides an option to erase existing Flash memory before writing onto it and allows you to confirm the erasure. The entire copying process takes several minutes and differs from network to network.

Before loading the switch from Flash memory, verify that the checksum of the bootstrap image in Flash memory matches the checksum listed in the README file that was distributed with the system software image.

The checksum of the bootstrap image in Flash memory is displayed at the bottom of the screen when you issue the copy rcp bootflash command. The README file was copied to the server automatically when you installed the system software.

Caution If the checksum value does not match the value in the README file, do not reboot the switch. Reissue the copy rcp bootflash command and compare the checksums again. If the checksum is repeatedly wrong, copy the original bootstrap image back into Flash memory before you reboot the switch from Flash memory. If you have a corrupted image in Flash memory and try to boot from Flash, the switch starts the system image (assuming booting from a network server is not configured).

Use the copy rcp running-config command to copy a configuration file from a network server to the switch's running configuration environment using rcp. You can copy either a host configuration file or a network configuration file. Accept the default value of host to copy and load a host configuration file containing commands that apply to one network server in particular. Enter value of network to copy and load a network configuration file containing commands that apply to all network servers on a network.

Use the copy rcp startup-configuration command to copy a host or network configuration file from a network server to the switch's startup configuration environment using rcp. Accept the default value of host to copy and store a host configuration file containing commands that apply to one network server in particular. Enter value of network to copy and store a network configuration file containing commands that apply to all network servers on a network.

The command copies a configuration file from the network server to the location specified by the config_file environment variable. The config_file environment variable specifies the configuration used during switch initialization.

The copy commands generally copy a file from a source to a destination. Some invalid combinations exist. Specifically, you cannot copy a running configuration to a running configuration, a startup configuration to a startup configuration, or TFTP to rcp.

The copy rcp command generally copies a file from a network server to another destination using rcp. If you do not specify a source or destination device, the switch uses the default device specified by the cd command.

When the destination is also specified by the config_file environment variable, the switch prompts you for confirmation before proceeding with the copy. To view the contents of the config_file environment variable, use the show boot command. To modify the config_file environment variable, use the boot config command. To save your modifications, use the copy running-config startup-config command.

Examples

The following example shows sample output resulting from copying a system image into a partition of Flash memory. The system prompts only if there are two or more read/write partitions or one read-only and one read/write partition and dual-Flash bank support in boot ROMs. If the partition entered is not valid, the process terminates. You have the option to enter a partition number, a question mark (?) for a directory display of all partitions, or a question mark and a number (?number) for a directory display of a particular partition. The default is the first read/write partition.

Switch# copy rcp flash
 
System flash partition information:
Partition   Size     Used    Free    Bank-Size   State       Copy-Mode
1       4096K    2048K   2048K   2048K       Read Only   RXBOOT-FLH
2       4096K    2048K   2048K   2048K       Read/Write  Direct
 
[Type ? no for partition directory; ? for full directory; q to abort]
Which partition? [default = 2]

If the partition is read-only and has dual-Flash bank support in boot ROM, the session continues as shown in the following display.

****  NOTICE  ****
Flash load helper v1.0
This process will accept the copy options and then terminate
the current system image to use the ROM based image for the copy.
Routing functionality will not be available during that time.
If you are logged in via telnet, this connection will terminate.
Users with console access can see the results of the copy operation.
---- ******** ----
Proceed? [confirm]
System flash directory, partition 1:
File  Length   Name/status
1   3459720  master/igs-bfpx.100-4.3
[3459784 bytes used, 734520 available, 4194304 total]
Address or name of remote host [255.255.255.255]? 131.108.1.1
Source file name? master/igs-bfpx-100.4.3
Destination file name [default = source name]?
 

The file is copied into the partition given by the user earlier.

Loading master/igs-bfpx.100-4.3 from 131.108.1.111: !
Erase flash device before writing? [confirm]
Flash contains files. Are you sure? [confirm]
Copy 'master/igs-bfpx.100-4.3' from TFTP server
as 'master/igs-bfpx.100-4.3' into Flash WITH erase? [yes/no] yes
 

If the partition is read-write, the session continues as follows.

System flash directory, partition 2:
File  Length   Name/status
1   3459720  master/igs-bfpx.100-4.3
[3459784 bytes used, 734520 available, 4194304 total]
Address or name of remote host [255.255.255.255]? 131.108.1.1
Source file name? master/igs-bfpx.100-4.3
Destination file name [default = source name]?
 

The file is copied into the partition given by the user earlier.

Accessing file 'master/igs-bfpx.100-4.3' on ABC.CISCO.COM...
Loading master/igs-bfpx.100-4.3 from 131.108.1.111: !
Erase flash device before writing? [confirm]
Flash contains files. Are you sure? [confirm]
Copy 'master/igs-bfpx.100-4.3' from TFTP server
as 'master/igs-bfpx.100-4.3' into Flash WITH erase? [yes/no] yes
 

The following example uses the copy rcp device command to copy the switch-image file from a network server using rcp to the Flash memory card inserted in slot 0 of the route processor card.

Switch# copy rcp slot0:switch-image

Related Commands

boot config
boot system flash
cd
config-register
copy flash rcp
copy running-config rcp
copy running-config startup-config
copy startup-config rcp
ip rcmd remote-username
show bootflash:

copy running-config

To copy the switch's running configuration file to another destination, use the copy running-config privileged EXEC command.

Syntax Description

Default

If you omit the destination device, the switch uses the default device specified by the cd command. If you omit the destination filename, the switch uses the source filename.

Command Mode

Privileged EXEC

Usage Guidelines

Save the configuration file to your startup configuration. This setup saves the configuration to the location specified by the config_file environment variable.

The copy running-config startup-config command replaces the write memory command. The copy running-config rcp or copy running-config tftp command replaces the write network command.

Related Commands

boot config
boot system flash
cd
config-register
copy running-config startup-config
copy startup-config rcp

copy startup-config

To copy the switch's startup configuration file to another destination, use the copy startup-config privileged EXEC command.

Syntax Description

Default

If you omit the destination device, the switch uses the default device specified by the cd command. If you omit the destination filename, the switch uses the source filename.

Command Mode

Privileged EXEC

Usage Guidelines

The copy commands generally copy a file from a source to a destination. Some invalid combinations exist. Specifically, you cannot copy a running configuration to a running configuration, a startup configuration to a startup configuration, or TFTP to rcp.

This command copies the configuration file pointed to by the config_file environment variable to another destination. To view the contents of the config_file environment variable, use the
show bootflash: command. To modify the config_file environment variable, use the
copy running-config startup-config command.

The rcp protocol requires that a client send the remote username of an rcp request to the server. When you issue the copy startup-config-rcp command, by default the switch software sends the username associated with the current TTY if that name is valid. For example, if the user is connected to the switch software through Telnet and the user was authenticated through the username command, the switch sends that username as the remote username.

To specify a different remote username to be sent to the server, use the ip rcmd remote-username command. You can also specify the path of an existing directory along with the remote username.

Caution The remote username must be associated with an account on the destination server. If you do not use the ip rcmd remote-username command to specify the name of a remote user associated with an account on the server, the remote username associated with the current TTY process must be associated with an account on the server. If there is no username for the current TTY process, the switch host name must be associated with an account on the server. If the network administrator of the destination server did not establish accounts for the remote username used, this command does not execute successfully when a default remote username is used.

If you copy the configuration file to a personal computer used as a server, the computer must support the rsh protocol.

Examples

The following example uses the copy startup-config command to copy the startup configuration file (specified by the config_file environment variable) to a Flash memory card inserted in slot 0 of the route processor card.

Switch# copy startup-config slot0:switch-config
 

The following is sample output from the copy startup tftp command.

Switch# copy startup tftp
Remote host []? 172.20.46.50
Name of configuration file to write [Switch-confg]? tftpboot/test-config
Write file tftpboot/test-config on host 172.20.46.50? [confirm]
Writing tftpboot/test-config !! [OK]

Related Commands

boot config
cd
copy rcp
copy running-config
ip rcmd remote-username
show bootflash:

copy tftp

To copy a file from a TFTP server to the switch or to another destination, use the copy tftp privileged EXEC commands.

Syntax Description

Default

If you omit the destination device, the switch uses the default device specified by the cd command. If you omit the destination filename, the switch uses the source filename. If you enter a cd command to the device, then that device becomes the default. For example, if you enter cd slot0: and then enter copy tftp bootflash, then "flash" means slot0.

Command Mode

Privileged EXEC

Usage Guidelines

Refer to the following guidelines:

• The system prompts for the address of the TFTP server and TFTP filename if you do not provide them at the command line.

• The system provides an option to erase existing internal Flash memory before copying to internal Flash memory.

• The entire copying process takes several minutes and differs from network to network.

Table 4-1 describes the characters that you might see during processing of the copy tftp command.

Table 4-1: copy tftp Character Descriptions

Character	Description
!	An exclamation point indicates that the copy process is taking place. Each exclamation point indicates that ten packets (512 bytes each) have been successfully transferred.
.	A period indicates the copy process timed out. Many periods in a row typically mean that the copy process might fail.
O	An uppercase O indicates a packet was received out of order and the copy process might fail.
e	A lowercase e indicates a device is being erased.
E	An uppercase E indicates an error and the copy process might fail.
V	A series of uppercase Vs indicates the progress during the verification of the image checksum.

When you enter the copy tftp flash command, the Flash memory checksum image displays on the bottom of the screen. Before booting from Flash memory, verify that this checksum identifier matches the checksum listed in the README file that was distributed with the system software image. You can find the README file on the TFTP server.

Caution If the checksum value is not correct according to the value in the README file, do not reboot the switch. Enter the copy tftp flash command and compare the checksums again. If the checksum is wrong, copy the original system software image back into Flash memory before you reboot the switch from Flash memory. If you have a corrupted image in Flash memory and try to boot from Flash, the switch starts the system image contained in ROM (assuming booting from a network server is not configured). If ROM does not contain a fully functional system image, the switch cannot function and must be reconfigured through a direct console port connection.

The copy commands generally copy a file from a source to a destination. Some invalid combinations exist. Specifically, you cannot copy a running configuration to a running configuration, a startup configuration to a startup configuration, or TFTP to rcp.

Switch# copy tftp bootflash

Boot flash directory:
File  Length   Name/status
  1   2622607  ls1010-xboot
[2622672 bytes used, 1571632 available, 4194304 total]
 
Address or name of remote host [255.255.255.255]? 223.255.254.254
Source file name? ls1010-xboot.101
Destination file name [ls1010-xboot.101]? 
Accessing file 'ls1010-xboot.101' on 223.255.254.254... 
Loading ls1010-xboot.101 from 223.255.254.254 (via Ethernet0): ! [OK]
 
Erase flash device before writing? [confirm]
Flash contains files. Are you sure you want to erase? [confirm]
 
Copy 'ls1010-xboot.101' from TFTP server into
     bootflash as 'ls1010-xboot.101' WITH erase? [yes/no] yes
Erasing device... eeeeeeeeeeeeeeee ...erased
Loading ls1010-xboot.101 from 223.255.254.254 (via Ethernet0): !!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 2622607/4194304 bytes]
 
Verifying checksum...  OK (0xE408)
Flash copy took 0:00:10 [hh:mm:ss]

boot config
boot system
cd
copy flash
show flash
verify

custom-queue-list

Posted: Mon Aug 16 14:30:46 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.