Quick Reference
Catalyst 8510 and

LightStream 1010
Hardware Information

Distance and Pinout Information

Maximum Transmission Distances

Transceiver Speed	Cable Type	Max. Distance Between Stations
10/100-Mbps Ethernet	Category 5 UTP	328 feet (100 m)
100-Mbps Ethernet	Multimode fiber	1640 feet (500 m)
1000-Mbps Ethernet	Multimode fiber	1640 feet (500 m)
1000-Mbps Ethernet	Single-mode fiber	16404 feet (5 km)
25-Mbps ATM	Category 5 UTP	328 feet (100 m)
155-Mbps ATM	Single-mode fiber	9 miles (15 km)
155-Mbps ATM	Single-mode fiber, long reach	18 miles (30 km)
155-Mbps ATM	Multimode fiber	1.2 miles (2 km)
622-Mbps ATM	Single-mode fiber	9 miles (15 km)
622-Mbps ATM	Single-mode fiber, long reach	25 miles (40 km)¹
622-Mbps ATM	Multimode fiber	1640 feet (500 m)
T1, 1.544-Mbps ATM	Category 5 twisted-pair	650 feet (198 m)
E1, 2.048-Mbps ATM	Category 5 twisted-pair and FTP (120 ohm)	650 feet (198 m)
E1, 2.048-Mbps ATM	Coaxial cable (75 ohm)	650 feet (198 m)
CDS3, 45-Mbps	Coaxial cable	450 feet (137 m)
CE1, 2.048-Mbps ATM	Category 5 twisted-pair	650 feet (198 m)
CES T1	Category 5 twisted-pair and FTP	650 feet (198 m)
CES E1	Category 5 twisted-pair and FTP (120 ohm)	820 feet (248.5 m)
CES E1	Coaxial cable (75 ohm)	650 feet (198 m)
DS3, 45-Mbps	Coaxial cable	450 feet (137 m)
E3, 34-Mbps	Coaxial cable	1299 feet (396 m)

¹If you are attaching a short cable to the 622-Mbps long-reach port adapter, you must add 10 dB of attenuation to the cable or the transmitter might overdrive the receiver and introduce data errors.

The 10/100 Mbps Ethernet interface module with unshielded twisted-pair (UTP) ports supports RJ-45 connectors.

Pin Signal Description

1

RXD+

Receive data +

2

RXD-

Receive data -

3

NC

No connection

4

NC

No connection

5

NC

No connection

6

NC

No connection

7

TXD+

Transmit data +

8

TXD-

Transmit data -

Pin	Signal	Description
1	RXD+	Receive data +
2	RXD-	Receive data -
3	NC	No connection
4	NC	No connection
5	NC	No connection
6	NC	No connection
7	TXD+	Transmit data +
8	TXD-	Transmit data -

Pinouts to RJ-48c Connectors

The T1, E1, CES T1 and CES E1 port adapters support RJ-48c connectors.

Pin Description

1

Receive ring

2

Receive tip

3

No connection

4

Transmit ring

5

Transmit tip

6

No connection

7

No connection

8

No connection

Pin	Description
1	Receive ring
2	Receive tip
3	No connection
4	Transmit ring
5	Transmit tip
6	No connection
7	No connection
8	No connection

Specifications and Regulatory Compliance Information

Description Specifications

Switch and processor capacity

10-Gbps shared memory, nonblocking switch fabric up to 32 KB frames

Dimensions (H x W x D)

Chassis: 10.4 x 17.25 x 18.4 in (26.4 x 43.1 x 46.0 cm)

Processor card and carrier module:

1.2 x 14.4 x 16 in (3.0 x 36.6 x 40.6 cm)

Port adapter: 1.2 x 6.5 x 10 in (3.0 x 16.5 x 25.4 cm)

Power supply: 2.7 x 6.0 x 15.3 in (6.9 x 15.2 x 38.9 cm)

Weight

Empty chassis: 32 lb (15.5 kg)

Fully populated chassis: approximately 130 lb (59.09 kg)

AC power supply: 11 lb (4.98 kg)

DC power supply: 10 lb (4.54 kg)

Airflow

95 cfm through the system fan assembly

Operating temperature

32 to 104

F (0 to 40

C)

Nonoperating temperature

-40 to 167

F (-40 to 75

C)

Humidity

10 to 90%, noncondensing

Altitude

-500 to 10,000 ft (-52 to 3048 m)

Microprocessor

100-Mhz MIPS R4700

AC total output

388W maximum

AC-input voltage

100-240 VAC wide input with power factor correction

AC frequency

Auto sensing limits: 100 to 127/200 to 240 VAC, 8/4A, 47 to 63 Hz

AC current rating

8/4A with the chassis fully populated

Power supply load

376W maximum configuration, 200W typical with max configuration

DC voltages supplied and steady-state maximum current ratings

System: +5V @ 70A

+12V @ 2A

+24V @ 0.2A

Processor: +5V @ 15A

+24V @ 25mA

+12V @ 500mA

Description	Specifications
Switch and processor capacity	10-Gbps shared memory, nonblocking switch fabric up to 32 KB frames
Dimensions (H x W x D)	Chassis: 10.4 x 17.25 x 18.4 in (26.4 x 43.1 x 46.0 cm) Processor card and carrier module: 1.2 x 14.4 x 16 in (3.0 x 36.6 x 40.6 cm) Port adapter: 1.2 x 6.5 x 10 in (3.0 x 16.5 x 25.4 cm) Power supply: 2.7 x 6.0 x 15.3 in (6.9 x 15.2 x 38.9 cm)
Weight	Empty chassis: 32 lb (15.5 kg) Fully populated chassis: approximately 130 lb (59.09 kg) AC power supply: 11 lb (4.98 kg) DC power supply: 10 lb (4.54 kg)
Airflow	95 cfm through the system fan assembly
Operating temperature	32 to 104 F (0 to 40 C)
Nonoperating temperature	-40 to 167 F (-40 to 75 C)
Humidity	10 to 90%, noncondensing
Altitude	-500 to 10,000 ft (-52 to 3048 m)
Microprocessor	100-Mhz MIPS R4700
AC total output	388W maximum
AC-input voltage	100-240 VAC wide input with power factor correction
AC frequency	Auto sensing limits: 100 to 127/200 to 240 VAC, 8/4A, 47 to 63 Hz
AC current rating	8/4A with the chassis fully populated
Power supply load	376W maximum configuration, 200W typical with max configuration
DC voltages supplied and steady-state maximum current ratings	System: +5V @ 70A +12V @ 2A +24V @ 0.2A Processor: +5V @ 15A +24V @ 25mA +12V @ 500mA

Description Specifications

Memory

8-MB Flash memory SIMM (upgradable to 16 MB)

64-MB DRAM

256-KB boot EPROM

128-KB SRAM

No Flash PC card installed by default (accepts 8-, 16-, or 20-MB Intel Series 2+ Flash PC cards)

Regulatory Compliance

UL 1950 (U.S.A.)

CSA 950 (Canada)

EN60950 (European Union)

IEC 950 (International)

AS/NZS 3260 (Australia/New Zealand)

TS001:1997 (Australia)

21CFR1040 (Laser - U.S.A.)

EN60825 (Laser - European Union)

IEC60825 (Laser - International)

CE Marking (European Union)

FCC Part 15 (CFR 47) Class A (U.S.A.)

VCCI Class A with UTP and Class B with FTP cables (Japan)

EN55022 Class A with UTP and Class B with FTP cables (European Union)

CISPR 22 Class A with UTP and Class B with FTP cables (International)

AS/NZS 3548 Class A with UTP and Class B with FTP cables (Australia/New Zealand)

Table of Contents