|
|
This chapter describes the commands and command syntax used to configure Cisco MC3810-IGX Interworking on the Cisco MC3810.
The following are the Cisco MC3810-IGX Interworking commands:
To configure a data connection that will travel over the FTC trunk to an IGX switch, use the connect global configuration command. To cancel the connection, use the no form of this command.
connect interface dlci dlci ftc-trunk connection-id cid
interface | Interface on the Cisco MC3810 on which the connection is configured. |
dlci | DLCI for the connection. |
ftc-trunk | Cisco MC3810 interface on which the FTC trunk was configured. |
cid | Connection ID. |
No data connection over the FTC trunk is configured.
Global configuration
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
When configuring a connection for an IP routing data connection over an FTC trunk, specify Switch0 for the local interface value.
When entering the DLCI value, do not use either of the following DLCIs:
The following example establishes a data connection on serial port 1:
connect Serial1 dlci 250 Serial0:0 connection-id 250
| Command | Description |
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk. | |
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface. | |
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810. | |
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810. | |
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI. | |
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810. |
To configure a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk, use the connect voice global configuration command. To disable the connection, use the no form of this command.
connect voice dial-peer-tag ftc-trunk connection-id cid
dlal-peer-tag | Voice dial-peer tag for the connection. Valid entries are 1 to 10000. The dial peer can be either a POTS dial peer or a VoFR dial peer. |
ftc-trunk | Cisco MC3810 interface on which the FTC trunk was configured. |
connection-id cid | Connection ID. |
No voice connection over the FTC trunk is configured.
Global configuration
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
The following example establishes a voice connection for dial peer 2 on serial port 0:
connect Voice2 Serial0:0 connection-id 50
| Command | Description |
Configures a data connection that will travel over the FTC trunk to an IGX switch. | |
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface. | |
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810. | |
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810. | |
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI. | |
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810. |
To enable FTC trunk encapsulation on a serial interface on the Cisco MC3810, use the encapsulation ftc-trunk interface configuration command. To disable FTC trunk encapsulation, use the no form of this command.
encapsulation ftc-trunkThis command has no keywords or arguments.
FTC trunk encapsulation is not enabled.
Interface configuration.
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
To configure FTC trunk encapsulation on serial interface 1 on the Cisco MC3810, enter the following commands:
interface serial 1 encapsulation ftc-trunk
| Command | Description |
Configures a data connection that will travel over the FTC trunk to an IGX switch. | |
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk. | |
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810. | |
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810. | |
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI. | |
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810. |
To map the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810, use the ftc-trunk frame-relay-dlci interface configuration command. To remove the FTC Frame Relay DLCI from the interface, use the no form of this command.
ftc-trunk frame-relay-dlci dlci [remote-frame-relay-dlci dlci]
dlci | Specifies the Frame Relay DLCI for the IGX switch. |
remote-frame-relay-dlci dlci | (Optional) Specifies the remote Frame Relay DLCI if there is a public Frame Relay cloud between the Cisco MC3810 FTC port and the IGX FTM port. Enter this option only if the local DLCI and the remote DLCI are not the same. |
No FTC trunk Frame Relay DLCI is configured.
Interface configuration
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
Do not enter the same DLCI that was assigned to the FTC management DLCI using the ftc-trunk management-dlci command.
The following example configures DLCI 200 as the FTC trunk Frame Relay DLCI:
interface serial 1 ftc-trunk frame-relay-dlci 200
| Command | Description |
Configures a data connection that will travel over the FTC trunk to an IGX switch. | |
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk. | |
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface. | |
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810. | |
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI. | |
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810. |
To map the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810, use the ftc-trunk management-dlci interface configuration command. To remove the FTC management DLCI from the interface, use the no form of this command.
ftc-trunk management-dlci dlci [remote-management-dlci dlci]
dlci | Specifies the Frame Relay DLCI for the IGX switch. |
remote-management-dlci dlci | (Optional) Specifies the remote management DLCI if there is a public Frame Relay cloud between the Cisco MC3810 FTC port and the IGX FTM port. Enter this option only if the local DLCI and the remote DLCI are not the same. |
No FTC trunk management DLCI is configured.
Interface configuration
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
The DLCI (or the remote DLCI if configured) must match the DLCI on the IGX switch configured using the IGX addad command.
The following example configures DLCI 100 as the FTC trunk management DLCI:
interface serial 1 encapsulation ftc-trunk ftc-trunk management-dlci 100
| Command | Description |
Configures a data connection that will travel over the FTC trunk to an IGX switch. | |
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk. | |
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface. | |
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810. | |
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI. | |
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810. |
To select the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI, use the ftc-management-protocol interface configuration command. To restore the default value, use the no form of this command.
ftc-trunk management-protocol {normal | inverted}
normal | Normal mode. |
inverted | Inverted mode. |
Normal mode is enabled.
Interface configuration
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
Use normal mode when the Cisco MC3810 is connected directly to the IGX switch. When two Cisco MC3810 concentrators are connected back-to-back, use inverted mode on one concentrator and normal mode on the other concentrator.
This command is available only when the ftc-trunk management-dlci command is configured.
The following example configures the FTC trunk management protocol to normal mode:
interface serial 1 encapsulation ftc-trunk ftc-trunk management-dlci 100 ftc-trunk management-protocol normal
| Command | Description |
Configures a data connection that will travel over the FTC trunk to an IGX switch. | |
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk. | |
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface. | |
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810. | |
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810. | |
Maps the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810. |
To map the FTC voice DLCI to an existing Frame Relay DLCI for voice traffic on the Cisco MC3810, use the ftc-trunk voice-dlci interface configuration command. To remove the FTC voice DLCI from the interface, use the no form of this command.
ftc-trunk voice-dlci dlci [remote-voice-dlci dlci]
dlci | Specifies the Frame Relay DLCI for the IGX switch. |
remote-voice-dlci dlci | (Optional) Specifies the remote voice DLCI If there is a public Frame Relay cloud between the Cisco MC3810 FTC port and the IGX FTM port. Enter this option only if the local DLCI and the remote DLCI are not the same. |
No FTC trunk voice DLCI is configured.
Interface configuration
| Release | Modification |
|---|---|
12.0(2) T | This command was first introduced. |
Do not enter the same DLCI that was assigned to the FTC management DLCI using the ftc-trunk management-dlci command.
The following example configures the FTC trunk voice DLCI:
interface serial 1 ftc-trunk voice-dlci 100
| Command | Description |
Configures a data connection that will travel over the FTC trunk to an IGX switch. | |
Configures a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk. | |
Enables FTC trunk encapsulation on a Cisco MC3810 serial interface. | |
Maps the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data traffic on the Cisco MC3810. | |
Maps the FTC management DLCI to an existing Frame Relay DLCI for management traffic on the Cisco MC3810. | |
Selects the mode on the Cisco MC3810 by which management frames are sent on the FTC trunk management DLCI. |
Posted: Mon May 3 15:11:16 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.