|
|
This appendix contains procedures for troubleshooting the Cisco AccessPath-TS3 Model 531 Integrated Access System hardware installation.
Your Cisco AccessPath-TS3 Model 531 system went through extensive testing before leaving the factory. However, if you encounter problems starting the system, use the information in this appendix to help isolate the cause of the problems. Problems with the initial startup are often caused by a switching module that has become dislodged from the backplane or a power supply that has been disconnected from the power cord connector.
This appendix contains the following sections:
Although temperature conditions above the maximum acceptable level rarely occur at initial startup, environmental monitoring functions are also included because they monitor DC line voltages.
When the initial system boot is complete, verify the following:
If each of these conditions is met and the hardware installation is complete, you probably have a software configuration problem. Refer to the Cisco AccessPath-TS3 Model 531 Integrated Access System Software Configuration Guide and the other documentation that shipped with your Cisco AccessPath-TS3 Model 531 system to troubleshoot the software.
However, if any of these conditions are not met, use the procedures in this appendix to isolate and, if possible, resolve the problem.
Figure A-1 on the following page shows the general troubleshooting strategy described in this appendix. Follow the steps presented in Figure A-1 to isolate problems to a specific subsystem and to resolve the problem.
If you are unable to easily solve the problem, contact a customer service representative for assistance and further instructions. Refer to the section "Contacting Customer Service," at the end of this appendix for more information on contacting customer service.
To troubleshoot the Cisco AccessPath-TS3 Model 531 system, you should know the significance of each of the LEDs on its shelves.
Figure A-2 through Figure A-4 show the location of the power OK LED on each of the shelves. At initial startup, the OK LEDs should flash on. After all devices have initialized, the LEDs should remain on. This indicates that each shelf is functioning properly.
The LEDs indicate the current operating condition of the Access Server Shelves. You can observe the LEDs, note any fault condition that the product is encountering, and then contact your system administrator or a customer service representative, if necessary.
Access Server Shelf T1 PRI Card Panel LEDs
| Chassis/Card | LED | State | Description |
|---|---|---|---|
Access Server Shelf chassis | Alarm | On | Alarm error has been detected. |
| AUI | Flickering Off | Ethernet LAN connection is transmitting and receiving data normally.
Ethernet LAN connection is not transmitting or receiving data. Check the Ethernet cable connections. | |
| Serial | Flickering | Associated serial port connection is transmitting and receiving data normally. | |
| System Status (Located to the right of the Console/Auxiliary ports) | Off
On Blinking | Power is off or system has not booted.
System is operating normally. Memory failure has occurred. | |
Quad T1 PRI1 card | Activity | Flickering | CSU/DSU2 in the card is communicating with a remote CSU/DSU. |
| Board OK | On | T1 PRI card has passed initial power-up diagnostics tests and is operating normally. | |
| Loopback | On | Local or remote loopback diagnostic test is running on the associated T1 port. | |
| Remote Alarm | On | Remote AIS has been received on the associated T1 port. The AIS3 is received on LOS4. | |
| Local Alarm | On | Associated T1 port has detected local LOS or OOF5 errors. | |
Quad E1 PRI card | Activity | Flickering | CSU/DSU in the card is communicating with a remote CSU/DSU. |
| Board OK | On | E1 PRI card has passed initial power-up diagnostics tests and is operating normally. | |
| Loopback | On | Local or remote loopback diagnostic test is running on the associated E1 port. | |
| 120 | On | Port is configured for 120-ohm line termination. | |
| Remote Alarm | On | Remote AIS has been received on the associated E1 port. The AIS is received on LOS. | |
| Local Alarm | On | The associated E1 port has detected local LOS or OOF errors. | |
12-Port Modem card | ACT (Activity) | Flickering | Modem card is processing transmit, receive, and modem interrupts normally. |
| OK (Board OK) | On Off | Modem card has passed the initial power-up diagnostic tests and is operating normally.
Fault condition is present on the card. |
This section describes the troubleshooting methods used in this appendix and describes how the Cisco AccessPath-TS3 Model 531 system shelves are divided into subsystems for more efficient problem solving. Each of the recommendations and procedures below applies to all of the shelves in the Cisco AccessPath-TS3 Model 531 system unless indicated otherwise.
The key to solving problems with the system is to isolate the problem to a specific system component or subsystem. Because startup problems can usually be attributed to a single component, it is more efficient to isolate the problem to a subsystem rather than troubleshoot each separate component in the system.
The Cisco AccessPath-TS3 Model 531 system shelves each consist of the following subsystems:
The following sections will help you isolate a problem to 1 of these subsystems and direct you to the appropriate troubleshooting section.
Startup problems might occur because of the source power or a board (network processing engine, I/O controller, or port adapter) that is dislodged from the midplane. Although an overtemperature condition is unlikely at initial startup, the environmental monitoring functions are included in this appendix because they also monitor internal voltages.
With the exception of the fan tray and network processing engine, LEDs indicate all system states in the startup sequence. By checking the state of the LEDs, you can determine when and where the system failed in the startup sequence. Use the following descriptions to isolate the problem to a subsystem, then proceed to the appropriate sections to try to resolve the problem.
LEDs indicate the status of all components (except for the system fan assembly) during the system startup sequence. By checking these LEDs, you can determine when and where the system failed.
When you start up the system by turning ON the power supply switch(es), the following should occur:
1 . At initial startup, the Power OK LEDs on each of the shelves should flash. After all devices have initialized, the Power OK LEDs should remain on. Refer to Figure A-5 through Figure A-8 for the location of the Power OK LED on each of the shelves.
2 . You should immediately hear the fans operating. They should be operating whenever system power is on.
3 . The power supply LEDs (for example, on the Switch Shelf, the PS1 or PS2 LEDs on the left side of the supervisor engine module faceplate) should all turn green immediately when you turn on the power supply switch. They should remain green during normal system operation.
4 . (Switch Shelf). The LEDs on the supervisor engine module should go on as follows:
5 . (Switch Shelf) only. The status LED on each switching module should turn green when the supervisor engine module completes initialization. This LED indicates that the switching modules are receiving power, have been recognized by the supervisor engine module, and contain a valid Flashcode version. However, it does not indicate the state of the individual interfaces on the switching modules. If a switching module Status LED is orange or red, proceed to the section "System-Level Troubleshooting Suggestions" section.
6 . The boot information and system banner should now be displayed. If they are not, refer to the section "Connecting the Console Port" in the chapter "Installing the Switch" in the Catalyst 5000 Series Hardware Installation and Maintenance Guide to verify that the terminal is set correctly and that it is properly connected to the supervisor engine module console port.
7 . The LEDs on the I/O controller should go on as follows:
8 . The enabled LED on each port adapter goes on when the network processing engine completes its initialization of the port adapter for operation. The enabled LED indicates that the port adapter is receiving power and has been recognized by the network processing engine; it does not indicate the state of the individual interfaces on the port adapters. If an enabled LED fails to go on, proceed to the section "Troubleshooting the Port Adapters".
9 . When all LEDs go on to indicate that the system has booted successfully, the initial system banner should be displayed on the console screen. If it is not displayed, refer to the section "Console and Auxiliary Port Connection Equipment" in the chapter "Installing the Cisco 7206" in the Cisco 7206 Installation and Configuration Guide to verify that the terminal is set correctly and that it is properly connected to the I/O controller's console port.
Check the following to isolate a power subsystem problem.
Step 1 Check the power supply LEDs. Is at least 1 power supply LED ON for each shelf?
(a) (Router Shelf Only) Make sure the power supply is flush with the back of the chassis. Check the clips that lock the cords into place.
(b) Make sure the power cable is connected at both ends.
(c) If both power LEDs were on previously and the power supply was operating, turn OFF the power switch, wait for the supply to cool, and turn the switch back ON. If the power supply LEDs remain off, there might be a problem with the input source or the power cable.
(d) Turn OFF the power to the switch, connect the power cord to another power source if one is available, and turn the power back ON. If the LED(s) then go on, the problem is the original power source.
(e) If the LED(s) fail to go on after you connect the power supply to a new power source, replace the power cord and then turn the switch back ON.
(f) If the LED(s) go on, return the original power cord for replacement. If they do not go on, repeat this step for the second (redundant) power supply cord.
(g) If the LED(s) still fail to go on when the switch is connected to a different power source using a new power cord, the power supply is probably faulty.
(h) If a second power supply is available, install it in the second power supply bay and contact a customer service representative for further instructions.
Step 2 Check the OK or PS LED for the redundant power supply. Is it on?
If you are unable to resolve the problem or if you determine that either a power supply or chassis connector is faulty, contact a customer service representative. See the section "Contacting Customer Service" at the end of this appendix.
The processor subsystem of the Router Shelf comprises the I/O controller, network processing engine, and all port adapters.
The I/O controller and network processing engine are required system components. The system cannot operate unless the I/O controller and network processing engine are installed properly; however, the system can operate without any port adapters installed as long as none are in partial contact with the midplane pins. A port adapter that is partially connected to the midplane will send incomplete signals to the processor, which will fault the PCI bus and cause the system to hang.
Therefore, first ensure that the I/O controller and the network processing engine are installed properly and the system software has initialized successfully. Then, if necessary, you can troubleshoot individual port adapters.
These procedures assume that the I/O controller, network processing engine, and router itself are in the original factory configuration, and that you have not made changes to your configuration file.
If the I/O controller LEDs do not go on as expected (refer to the section "Identifying Startup Problems". Check the following items to help isolate the problem:
These procedures assume that the I/O controller, network processing engine, and router itself are in the original factory configuration, and that you have not made changes to your configuration file.
If the I/O controller enabled LED does not go on as expected, make sure the power to the router is turned OFF, reseat the network processing engine in its slot, and restart the router.
If the enabled LED remains off, the system detected a processor hardware failure. (This LED should be on in normal operation.) Contact a service representative for instructions.
Check the following to help isolate a problem with the port adapters:
Check the following items to help isolate a problem with the cooling subsystem (fan assembly):
1 . When you start up the system, do the fans start operating?
2 . The following message, if displayed, indicates that the system has detected an overtemperature condition or out-of-tolerance power inside the chassis:
3 . (Switch Shelf only.) Check the fan LED on the supervisor engine module. Is it green?
4 . Check the fan LED again. Is it still orange?
If yes, the system has detected a fan assembly failure.
If you experience trouble with the startup that is not resolved with these procedures, contact a service representative for assistance and further instructions.
Check the following items to help isolate a supervisor engine module or switching module problem:
If you still experience trouble with the startup, contact a customer service representative for assistance.
Use the following suggestions to assist in isolating or solving a system problem:
If you are unable to solve a startup problem after using the troubleshooting suggestions in this appendix, check the online documentation available on the World Wide Web. (For more information, see the section "Related and Referenced Documents" in the preface "About This Guide.")
If you are still unable to resolve a startup problem, contact a customer service representative for assistance and further instructions. Before you call, have the following information ready to help your customer service representative assist you as quickly as possible:
|
|