Table of Contents

Installing the Kit on Cisco 3620 and Cisco 3640 Routers

Installing the Grounding Lug

Applying Labels to the Power Supplies

Installing the Kit on Cisco 3620 and Cisco 3640 Routers

This chapter describes how to install a NEBS Level 3/ETSI kit on your Cisco 3620 or Cisco 3640 router.

This chapter contains the following sections:

Installing the Grounding Lug

Follow this procedure to attach the grounding lug to your router chassis:

Step 1 Turn OFF power to the router. However, to channel ESD voltages to ground, do not unplug the power cable. Remove all network interface cables, including telephone cables, from the rear panel.

The following warning applies to routers that use a DC power supply:

Warning
Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.

Step 2 Use the number 2 Phillips screwdriver to remove either of the following:

One mounting screw from the power supply on the right side of the Cisco 3620 router's rear panel.
Two mounting screws from the power supply on the right side of the Cisco 3640 router's rear panel.

Figure 4-1 and Figure 4-2 show Cisco 3620 DC and AC power supplies, whereas Figure 4-3 and Figure 4-4 show Cisco 3640 DC and AC power supplies. The DC and AC power supplies for these router models differ in appearance, but the number and position of the mounting screws are the same.

Figure 4-1: Cisco 3620 DC Power Supply Mounting Screw

Figure 4-2: Cisco 3620 AC Power Supply Mounting Screw

Figure 4-3: Cisco 3640 DC Power Supply Mounting Screws

Figure 4-4: Cisco 3640 AC Power Supply Mounting Screws

Step 3 Attach the bracket over the power supply using the screw(s) you removed in Step 2. (See Figure 4-5 and Figure 4-6.)

Figure 4-5: Attaching the Bracket over the Cisco 3620 Power Supply

Figure 4-6: Attaching the Bracket over the Cisco 3640 Power Supply

Step 4 Strip one end of the 6-AWG wire to expose approximately 0.75 inch (20 mm).

Step 5 Crimp the grounding lug around the wire. (See Figure 4-7.)

Figure 4-7: Crimping the Lug Around the Wire

Step 6 Use the number 2 Phillips screwdriver to fasten the grounding lug to the bracket on Cisco 3620 and Cisco 3640 routers. (See Figure 4-8 through Figure 4-10.)

Note

RPS unit, fasten the grounding lug to its bracket diagonally as shown in

Figure 4-8: Grounding Lug Fastened to Bracket on Cisco 3620 Power Supply

Figure 4-9: Grounding Lug Fastened to Bracket on Cisco 3620 Power Supply with RPS

Figure 4-10: Grounding Lug Fastened to Bracket on Cisco 3640 Power Supply

Step 7 Connect the other end of the grounding lug wire to a grounding point at your site.

Applying Labels to the Power Supplies

Step 1 If you have a Cisco 3620 router, apply the "Disconnect All Connections Before Opening the Cover" label to the upper part of the power supply. (See Figure 4-11.)

If you have a Cisco 3640 router, apply the "Disconnect All Connections Before Opening the Cover" label to the upper part of the power supply, and apply the supplied voltage rating label for your power supply to the lower part of the bracket. (See Figure 4-12.)

Figure 4-11: Cisco 3620 Power Supply Labels

Figure 4-12: Cisco 3640 Power Supply Labels

Step 2 Reinstall network cables, and turn ON power to the router.

Caution
NEBS/ETSI Intrabuilding Lightning Requirement
This equipment is suitable for connection to intrabuilding or nonexposed wiring or cabling only. This cabling must be shielded.

The following warning applies to routers that use a DC power supply:

Warning
After wiring the DC power supply, remove the tape from the circuit breaker switch handle and reinstate power by moving the handle of the circuit breaker to the ON position.

Posted: Thu Jul 29 09:29:36 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.