|
|
Product Numbers: ONS15304-I/O-PNL=
This document describes the Cisco Optical Networking System (ONS) 15304 router distribution panel. The Cisco Optical Networking System (ONS) 15304 router is referred to in this document as the Cisco ONS 15304.
Use this document in conjunction with the Cisco Optical Networking System 15304 Hardware Installation Guide and the Regulatory Compliance and Safety Information document for the Cisco ONS 15304. If you have questions or need help, refer to the "Cisco Connection Online" section.
This document includes the following sections:
Additional maintenance procedures are described on the Documentation CD-ROM that shipped with your Cisco ONS 15304.
Follow these guidelines to ensure general safety:
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might harm you. A warning symbol precedes each safety warning.
Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.
Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d'avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil.
Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Dokument Regulatory Compliance and Safety Information (Informationen zu behördlichen Vorschriften und Sicherheit), das zusammen mit diesem Gerät geliefert wurde.
Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nel documento Regulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositivo.
Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i dokumentet Regulatory Compliance and Safety Information (Overholdelse av forskrifter og sikkerhetsinformasjon) som ble levert med denne enheten.
Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo.
¡Advertencia! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. Para ver una traducción de las advertencias que aparecen en esta publicación, consultar el documento titulado Regulatory Compliance and Safety Information (Información sobre seguridad y conformidad con las disposiciones reglamentarias) que se acompaña con este dispositivo.
Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. Se förklaringar av de varningar som förkommer i denna publikation i dokumentet Regulatory Compliance and Safety Information (Efterrättelse av föreskrifter och säkerhetsinformation), vilket medföljer denna anordning.
 | Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units. |
| Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord. |
The following warning applies to routers with a DC power supply:
| Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. |
| Warning Ultimate disposal of this product should be handled according to all national laws and regulations. |
 | Caution To avoid damaging electrostatic discharge (ESD)-sensitive components, ensure that you have discharged all static electricity from your body before opening the chassis. |
| Warning The Ethernet 10BaseT, serial, console, and auxiliary ports contain safety extra-low voltage (SELV) circuits. BRI circuits are treated like telephone-network voltage (TNV) circuits. Avoid connecting SELV circuits to TNV circuits. |
| Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. |
Follow these guidelines when working on equipment powered by electricity:
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Always follow ESD prevention procedures when removing and replacing cards. Ensure that the router chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis frame to safely channel unwanted ESD voltages to ground. To properly guard against ESD damage and shocks, the wrist strap and cord must be used correctly. If no wrist strap is available, ground yourself by touching the metal part of the chassis.
| Caution For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms (Mohm). |
| Caution Before opening the chassis, be sure that you have discharged all static electricity from your body and the power is OFF. |
| Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units. |
The Cisco ONS 15304 distribution panel is used to break out individual E1 and Ethernet ports from the Cisco ONS 15304. The distribution panel is shown in Figure 1.
The distribution panel has the following components:
 | Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. |
| Warning Connect to a -48/60 VDC source that is electrically isolated from an AC source and is reliably connected to earth. |
| Warning Care must be given to connecting units to the supply circuit so that wiring is not overloaded. |
To ground the Cisco ONS 15304 distribution panel, you need:
Before you install any modules or attach cables or connectors, ground the Cisco ONS 15304 distribution panel chassis.
| Warning Operating ungrounded electrical equipment can result in severe electrical shock and damage the equipment. |
Step 1 Find the grounding screw holes on the front of the Cisco ONS 15304 distribution panel. (See Figure 1.)
Step 2 Secure the ground wire to the standard barrel two-hole lug.
Step 3 Fasten the wire and lug to the distribution panel with the two green number 10-32 screws from the accessory kit.
Step 4 Connect the other end of the copper wire to earth ground.
This section describes the pinouts for the Cisco ONS 15304 distribution panel ports.
| Description | 50-Pin Telco E11 |
|---|---|
TRING1 | pin 1 |
RRING1 | pin 2 |
TRING2 | pin 4 |
RRING2 | pin 5 |
TRING3 | pin 7 |
RRING3 | pin 8 |
TRING4 | pin 10 |
RRING4 | pin 11 |
TRING5 | pin 13 |
RRING5 | pin 14 |
TRING6 | pin 16 |
RRING6 | pin 17 |
A-OUT-RING | pin 18 |
TRING7 | pin 19 |
RRING7 | pin 20 |
A-IN-RING | pin 21 |
TRING8 | pin 22 |
RRING8 | pin 23 |
B-OUT-RING | pin 24 |
B-IN-RING | pin 25 |
TTIP1 | pin 26 |
RTIP1 | pin 27 |
TTIP2 | pin 29 |
RTIP2 | pin 30 |
TTIP3 | pin 32 |
RTIP3 | pin 33 |
TTIP4 | pin 35 |
RTIP4 | pin 36 |
TTIP5 | pin 38 |
RTIP5 | pin 39 |
TTIP6 | pin 41 |
RTIP6 | pin 42 |
A-OUT-TIP | pin 43 |
TTIP7 | pin 44 |
RTIP7 | pin 45 |
A-IN-TIP | pin 46 |
TTIP8 | pin 47 |
RTIP8 | pin 48 |
B-OUT-TIP | pin 49 |
B-IN-TIP | pin 50 |
| 1Pins not shown are not connected. |
| Description | IN DB-251 |
|---|---|
RTIP1 | pin 1 |
RRING1 | pin 2 |
RTIP2 | pin 4 |
RRING2 | pin 5 |
RTIP3 | pin 7 |
RRING3 | pin 8 |
RTIP4 | pin 10 |
RRING4 | pin 11 |
GND | pin 13 |
RTIP5 | pin 15 |
RRING5 | pin 16 |
RTIP6 | pin 18 |
RRING6 | pin 19 |
RTIP7 | pin 21 |
RRING7 | pin 22 |
RTIP8 | pin 24 |
RRING8 | pin 25 |
| 1Pins not shown are not connected. |
| Description | OUT DB-251 |
|---|---|
TTIP1 | pin 1 |
TRING1 | pin 2 |
TTIP2 | pin 4 |
TRING2 | pin 5 |
TTIP3 | pin 7 |
TRING3 | pin 8 |
TTIP4 | pin 10 |
TRING4 | pin 11 |
GND | pin 13 |
TTIP5 | pin 15 |
TRING5 | pin 16 |
TTIP6 | pin 18 |
TRING6 | pin 19 |
TTIP7 | pin 21 |
TRING7 | pin 22 |
TTIP8 | pin 24 |
TRING8 | pin 25 |
| 1Pins not shown are not connected. |
| Description | Clock Port A1 |
|---|---|
GND | pin 1 |
A-OUT-TIP | pin 2 |
GND | pin 3 |
A-IN-TIP | pin 4 |
A-OUT-RING | pin 6 |
GND | pin 7 |
A-IN-RING | pin 8 |
| 1Pins not shown are not connected. |
| Description | Clock Port B1 |
|---|---|
GND | pin 1 |
B-OUT-TIP | pin 2 |
GND | pin 3 |
B-IN-TIP | pin 4 |
B-OUT-RING | pin 6 |
GND | pin 7 |
B-IN-RING | pin 8 |
| 1Pins not shown are not connected. |
| Description | G.701 E1 DB-151 |
|---|---|
TRING | pin 2 |
GND | pin 7 |
RTIP | pin 8 |
TTIP | pin 9 |
GND | pin 10 |
RRING | pin 15 |
| 1Pins not shown are not connected. |
| Description | Telco 50-Pin Ethernet Port1 |
|---|---|
RXD1_M | pin 2 |
TXD1_M | pin 3 |
RXD2_M | pin 5 |
TXD2_M | pin 6 |
RXD3_M | pin 8 |
TXD3_M | pin 9 |
RXD4_M | pin 11 |
TXD4_M | pin 12 |
RXD5_M | pin 14 |
TXD5_M | pin 15 |
RXD6_M | pin 17 |
TXD6_M | pin 18 |
RXD7_M | pin 20 |
TXD7_P | pin 21 |
RXD8_M | pin 23 |
TXD8_M | pin 24 |
RXD1_P | pin 27 |
TXD1_P | pin 28 |
RXD2_P | pin 30 |
TXD2_P | pin 31 |
RXD3_P | pin 33 |
TXD3_P | pin 34 |
RXD4_P | pin 36 |
TXD4_P | pin 37 |
RXD5_P | pin 39 |
TXD5_P | pin 40 |
RXD6_P | pin 42 |
TXD6_P | pin 43 |
RXD7_P | pin 45 |
TXD7_P | pin 46 |
RXD8_P | pin 48 |
TXD8_P | pin 49 |
| 1Pins not shown are not connected. |
| Description | Ethernet RJ-451 |
|---|---|
RXD_P | pin 1 |
RXD_M | pin 2 |
TXD_P | pin 3 |
TXD_M | pin 6 |
| 1Pins not shown are not connected. |
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar, select Documentation, and click Enter the feedback form. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
Posted: Wed Feb 23 11:15:05 PST 2000
Copyright 1989 - 2000©Cisco Systems Inc.
