|
|
This document describes the basic process of cabling and configuring the Internet access device, the Cisco 700 series router. For advanced cabling information, refer to the Cisco 700 Series Router Installation Guide. For advanced configuration information, refer to the Cisco 700 Series Router Command Reference and the Cisco 700 Series Router Software Configuration Guide. These documents can be found on the Cisco Documentation CD-ROM and Cisco Connection Online (CCO).
 |
Note Additional parts might be required to install Cisco775 and Cisco 776 routers. An Ethernet crossover cable must be used to connect a hub to the router. Depending on the country, you might need a phone port adapter to connect an analog telephone. These parts must be provided by the user. |
Before you begin, verify that each computer that will be connected to the computer has a network interface card (NIC) installed and TCP/IP loaded.
If you are connecting the router to a hub, connect the yellow Ethernet cable from the yellow Ethernet port on the rear panel of the router to an Ethernet port on the hub.
Step 2 If you are connecting the router to a computer, to a hub, set the node-hub switch to the "NODE" position and connect the computers to the hub as described in the documentation provided with your hub. 
Step 2 If you are connecting to a hub, connect an Ethernet crossover cable (not included) from a yellow Ethernet port on the rear panel of the router to an Ethernet port on the hub. Otherwise omit this step.
This section shows how to connect the router to the ISDN.
Step 2 Connect the other end of the ISDN U cable directly to an RJ-45 ISDN wall jack.
|
Note If necessary, use the enclosed RJ-45-to-RJ-11 adapter to connect to an RJ-11 ISDN wall jack. |
Step 2 Connect the other end of the ISDN S/T cable to the ISDN wall socket.
|
Note If necessary, use the enclosed RJ-45-to-RJ-11 adapter to connect to an RJ-11 ISDN wall jack. |
This section describes the procedure for supplying power to the router.
Step 2 Turn on the router by using the on/off switch on the rear panel. The green RDY LED (and the NT1 LED on the Cisco 772 and Cisco 776) on the front panel of your router turns on. Your router is now ready to be set up.
If the green RDY LED is not on, refer to the "Troubleshooting Cisco 700 Series Routers" chapter in the Cisco 700 Series Router Installation Guide.
A Cisco Fast Step CD-ROM and a RVS-COM Lite CD-ROM is included with your router. We recommend that you use Cisco Fast Step software to set up the router and RVS-COM Lite software for Common ISDN Application Programmers Interface (CAPI) support.
Cisco Fast Step software simplifies the setup and monitoring of Cisco routers. It runs on Microsoft Windows 95, Windows 98, and Windows NT 4.0 personal computer systems. The Cisco Fast Step software CD-ROM is included with your router. It is also available on Cisco Connection Online at http://www.cisco.com/pcgi-bin/tablebuild.pl/faststep. If you have questions about Cisco Fast Step software, please E-mail the following alias for more information: cs-faststep@cisco.com
Insert the CD in the CD-ROM drive. The installation wizard starts automatically.
If you inserted the CD in the drive and the setup program did not start automatically, launch the installation wizard by following these instructions:
Step 2 Double-click the CD icon.
Step 3 Double-click the ImLanguageSelect.exe icon, and follow the on-screen instructions.
If you downloaded the software from Cisco Connection Online, launch the installation wizard by following these instructions:
Step 4 Uncompress the Cisco Fast Step files, retaining the directory structure.
Step 5 Double-click the Setup.exe icon in the disk1 directory, and follow the on-screen instructions.
The RVS-COM Lite software provides CAPI support. If you already have a terminal adapter with CAPI installed, you must uninstall the old version of CAPI, install a network interface card, and install the Cisco-supplied RVS-COM Lite upgrade on every PC.
Make sure you do the following:
Place the RVS-COM Lite CD into the CD-ROM drive of your computer. It should start automatically. If it does not start or you have any questions about the RVS-COM Lite software, refer to the documentation provided with the RVS-COM Lite CD-ROM.
Posted: Tue Mar 28 08:30:53 PST 2000
Copyright 1989 - 2000©Cisco Systems Inc.