|
|
The Catalyst 8500 CSR family of Campus Switch Routers provides the next-generation switching paradigm for both switching performance and critical network services. Including support for all IP and IPX routing standards, the Catalyst 8500 CSR family of campus backbone switches offers a complete suite of sophisticated features. The Catalyst 8500 CSR family contains several key components of the new enterprise campus network architecture, providing for high-speed performance, resiliency, quality of service (QoS), and security within the network backbone. With new ATM and Packet-over-SONET uplinks, the Catalyst 8540 CSR delivers metropolitan area network (MAN)/wide area network (WAN) solutions with scalable performance, lower cost of ownership, and the features needed in New World Networks. The Catalyst 8500 CSR family offers a complete set of campus-required features such as Hot Standby Router Protocol (HSRP), Protocol Independent Multicast (PIM) for multicast routing, and a full set of routing protocols, including Routing Information Protocol (RIP), RIP version 2, Open Shortest Path First (OSPF), Interior Gateway Routing Protocol (IGRP), Enhanced IGRP, and Border Gateway Protocol (BGPv4). As QoS mechanisms become more important in the campus, the Catalyst 8500 CSR family provides, in its first phase, four queues per port based on IP precedence. In the following phase, the Catalyst 8500 CSR family will provide support for a more granular method of determining QoS and ensuring minimal latency and packet loss for mission-critical applications. The Catalyst 8500 CSR family delivers the performance, scalability, and robustness required for network production backbones. The Catalyst 8510 CSR delivers wire-speed IP and IPX performance for all ports, scaling to 6 million pps. The Catalyst 8540 CSR delivers the same wire speed functionality for IP and IPX, scaling to 24 million pps. With the Catalyst 8500 CSR family, Cisco ensures investment protection and migration to new technologies. The Catalyst 8510 CSR offers redundant power supply modules and uses the same power supplies used for the Catalyst 5000 and LightStream 1010 chassis. The Catalyst 8540 CSR provides a high level of system redundancy, providing for redundant switch fabrics, route processors and power supply modules. Wire-speed performance, scalable control, and rich QoS capabilities of the Catalyst 8500 CSR family allow network managers to smoothly integrate the Catalyst 8500 CSR with the Catalyst 8500 MSR, Catalyst 5000, Catalyst 6000, Cisco 7500/7200, LightStream 1010, BPX 8600, MGX 8800, IGX 8400, MC 3810, and the 3600/2600 product families. Using a Cisco end-to-end solution, they can create a unique solution that truly meets the end-to-end QoS requirement for differentiated services in the enterprise. The Catalyst 8500 CSR allows smooth integration into existing networks by incorporating Cisco IOS-based routing protocols (IGRP, EIGRP, OSPF, and BGPv4) that are proven, time tested, reliable, and fast converging Layer 3 backbones. New ATM and Packet-over-SONET uplinks for the Catalyst 8540 CSR enable new metropolitan area network (MAN)/wide area network (WAN) applications. These new features and enhanced Layer 3 features supported on the 8500 CSR family are described below. Catalyst 8500 CSR — Campus Switch Router
Product Overview
Key Features and Benefits
New Features
|
Feature |
Benefit |
|---|---|
|
ATM and Packet-over-SONET Uplinks for the Catalyst 8540 CSR |
Catalyst 8540 CSR customers can now more effectively scale their MAN/WAN infrastructure when using the OC-3c/OC-12c ATM and OC-12c Packet-Over-SONET (POS) Uplinks. These uplinks provide one uplink port coupled with one Enhanced Gigabit Ethernet port. Advanced features include built-in ACL functionality, up to 256K routing table entries, and enhanced QoS features (future). |
|
Two-port Enhanced Gigabit Ethernet Module for the Catalyst 8540 |
The Two-port enhanced Gigabit Ethernet module is ideal for supporting L3 and gigabit backbone applications for wire-speed performance for the Catalyst 8540. Advanced features include built-in ACL functionality, up to 256K routing table entries, and enhanced QoS features (future). |
|
Access Control Daughter Card (ACL) for the Catalyst 8510/ LightStream 1010 |
L3 security is now available for the Catalyst 8510/LS1010 via the Access Control Daughter Card (ACL), allowing customers to extend traffic control and security capabilities beyond control-plane access lists. |
|
Feature |
Comment/Description |
Benefit |
|---|---|---|
|
High Performance, High Scalability |
||
|
Wire-Speed, Low-Latency Switching for IP, IPX, IP Multicast, and Layer 2 Bridging |
Catalyst 8510---6 million pps, 10G nonblocking switching fabric Catalyst 8540---24 million pps, 40G nonblocking switching fabric |
Nonblocking performance means that the total switching capacity of each Catalyst 8500 series platform is greater than what is needed to switch the total traffic load across all the respective interfaces simultaneously, even if all the traffic is to be routed. |
|
Cisco Express Forwarding (CEF) |
Same switching paradigm used to scale Cisco 7500 and GSR 12000 series routers by isolating control plane (routing) and data plane (switching) |
CEF, designed originally to solve Internet scalability issues, provides needed scalability to emerging enterprise intranets and applications. |
|
Hardware-Based Routing Tables on Each Port |
Cisco`s highly optimized lookup algorithm, the FIB, is downloaded to the ASICs on each line card |
This optimized algorithm, together with the CEF architecture, ensures that the route processor is free to keep the network topology consistent and to converge quickly in the event of topology changes or link failures. |
|
MAN/WAN Uplink Capabilities |
OC-3c/OC-12c ATM Uplink with 1-port Enhanced Gigabit Ethernet port OC-12c Packet-over-SONET Uplink with 1-port Enhanced Gigabit Ethernet port |
ATM and Packet-over-SONET (POS) uplink support Built-in Access Control List (ACL) capabilities Up to 256K routing table entries Enhanced QoS support (future) MPLS VPN/CoS support (future) |
|
Enhanced Gigabit Ethernet Modules |
2-port Enhanced Gigabit Ethernet Module |
Built-in Access Control List (ACL) capabilities Up to 256K routing table entries Enhanced QoS support (future) MPLS VPN/CoS support (future) |
|
Catalyst 8510 CSR is R4600 RISC-Based |
100 MHz clock speed |
High performance meets requirements for quick convergence of routing protocols upon topology changes or link failures and for running resource and policy admission control, and son. |
|
Catalyst 8540 CSR is R5000 RISC-Based |
200 MHz clock speed | |
|
Cisco IOS Routing Support |
||
|
Cisco IOS IP Routing Support |
OSPF BGPv4 EIGRP IGRP RIP RIP-2 CIDR support VLSM IP multicast: PIM—sparse and dense mode and DVMRP interoperability support |
Consistent LAN and WAN implementation Fast convergence around failures with OSPF and EIGRP Stable, time-tested, and proven industry-standard routing protocol feature set |
|
Cisco IOS IP Routing Support |
RIP EIGRP |
Fast convergence around failures with EIGRP Stable, time-tested and proven industry-standard routing protocol feature set |
|
Integrated Routing and Bridging (IRB) |
Both routing and bridging on ports or sets of ports |
Supports non-routable protocols and facilitates some address transition plans. |
|
HSRP |
Cisco value add protocol for router redundancy |
Network redundancy and load-sharing with smooth integration into existing Cisco networks; fail-over transparent tend users. |
|
Rich QoS |
||
|
Nonblocking, Shared-Memory Switching Fabric with Low Latency and Rich Mechanisms for Queuing and Scheduling |
Dynamic allocation of shared memory maximizes performance and flexibility with a high degree of effective buffer utilization |
Supports all IP QoS and IEEE 802.1Q traffic classes and allows for reservations on demand while minimizing packet loss. |
|
Integrated into CiscoAssure Policy Networking Architecture |
Integral part of end-to-end QoS architecture |
Provides simple means to define policies that prioritize users or applications in the network. |
|
Per-Flow Queuing |
Granular traffic queuing capability |
Differentiate and protect mission-critical applications from other traffic. |
|
Weighted Round Robin (WRR) |
Differentiated queue scheduling discipline |
Fair, differentiated delay probability for traffic classes, including multiple IP Precedence levels, ToS, or RSVP service classes. |
|
Per-Queue Drop Thresholds |
Supports early discarding of packets when user-defined buffer threshold(s) are exceeded |
Multiple thresholds offer differentiated loss probability for multiple IP Precedence level or ToS service classes. |
|
Traffic Policing and Rate Limiting |
Token bucket algorithm for frame switching (future) |
Ensures that traffic reservations are guaranteed by protecting against misbehaving or noncompliant traffic. |
|
Resource and Policy Admission Control |
RSVP reservations and other emerging reservation routing protocols require sophisticated resource and policy admission control algorithms |
Ensures that guarantees made to existing flows or policies set by CiscoAssure can be honored when setting up new reservations. |
|
Cisco IOS Intelligent Network Services |
||
|
Mobility |
DHCP BOOTP relay Local-area mobility |
Offers numerous options to support dynamic IP addressing in environments with frequently moving desktops, as well as transition to DHCP deployment strategies |
|
Routing Security |
MD5 route authentication |
Prevents unauthorized routers from interrupting trusted router operations |
|
VLANs |
Cisco ISL802.1Q |
Allows multiple subnets to be overlaid logically between the backbone and wiring closets Allows smooth integration with installed Catalyst LAN switches |
|
Load Sharing Across Redundant Links |
Support for Fast EtherChannel and Gigabit EtherChannel Support for parallel links using unique Layer 3 load-balancing algorithm |
Increases effective link bandwidth and network uptime |
|
Manageability Mechanisms |
||
|
Uninterrupted Software Upgrades |
The Catalyst 8540 CSR can be deployed with two route processor modules where the secondary module can be loaded with a new software image and become the primary without any need to reboot or without any loss of traffic or connectivity Catalyst 8510 CSR supports seamless software upgrades on its SRP |
Eases maintenance and reduces mean time to repair (MTTR) |
|
Telnet, TFTP, and BOOTP |
Standard mechanisms for software downloads and configuration input/output |
Facilitates easy and flexible configuration |
|
Flash Memory for Software Download |
Allows storage of multiple images and configuration files Remotely downloads new software revisions without hardware changes |
Reduces cost of administering software upgrades by providing centralized network management and local storage capability. |
|
Cisco Discovery Protocol (CDP) |
Auto-discovers Cisco devices in a network |
Reliable topology discovery for network management system. |
|
IP Ping, Trace Route |
Standard IP management mechanisms |
Allows network administrator to verify path integrity at any intermediate point Facilitates network troubleshooting |
|
RMON MIB |
Four groups (many of the traditional RMON data sets such as alarms, events, statistics, and history) |
Ease of management and proactive troubleshooting |
|
RMON Traps |
Can be applied to any MIB variable |
Allows customized monitoring of switch operation |
|
Text-Based CLI |
Uses Cisco router CLI parser, accessible through local terminal or Telnet |
Uses familiar Cisco CLI for online help, scripts and extensive debugging capabilities Facilitates smooth integration into Cisco router network |
|
Local Management Ports on SRP/MSRP in Catalyst 8510 and on the RP/SRP Module in Catalyst 8540 |
Ethernet port Dual EIA/TIA-232 serial ports |
Out-of-band management using parallel 10 MB Ethernet network Allows support for local terminal and modem for remote management |
|
Access Protection Mechanisms |
Multiple password levels and TACACS+, RADIUS, or AAA for device management access |
Precludes unauthorized access to the Catalyst 8500, preventing "hacking" of configuration |
|
Chassis |
||
|
Modular, 5- and 13-Slot Chassis |
Supports required switch and route module(s) and up to four or eight line cards |
Allows users to flexibly add or mix and match number and type of line modules, as needed |
|
Catalyst 8510 CSR Uses the Same Chassis Footprint as Catalyst 5000 and LightStream 1010 |
Common power supplies and fan tray |
Allows for leveraging investments in spares |
|
Fits Standard 19-Inch Rack |
Works with existing wiring closet racks Mounts at front or rear of chassis Rack-mounting hardware and cable guides included |
Ensures ease of installation in wiring closet and network center |
|
Dual, Fault-Tolerant Power Supplies |
Can configure one or two power supplies, where the second provides redundancy Both AC and DC (-48V) options available |
Offers option of increased reliability for fault-tolerant configurations |
|
Dual Power Cords |
One teach power supply |
Can be powered by independent power sources or distribution systems for greater reliability |
|
Field-Replaceable Fan Tray |
Supports multiple redundant fans |
Eases maintenance and reduces MTTR |
|
Field-Replaceable SRP Module in the Catalyst 8510 CSR and Field-Replaceable SP and RP Modules in the Catalyst 8540 CSR |
The Catalyst 5500 does not need to be powered down to replace the SRP/MSRP |
Eases maintenance and reduces MTTR |
|
Description |
Specification |
|---|---|
|
Technology |
Thirteen-slot chassis and fan tray Optional redundant AC or DC, auto-sensing, load-sharing power supplies, each with its own power cord C8541CSR-RP and C8542CSR-SP modules running L3 Cisco IOS software 40 Gbps shared memory, nonblocking fabric 16 MB of Flash memory standard, plus up to 20 MB through PC Flash cards 256 MB DRAM system memory Ethernet port for out-of-band management Dual EIA/TIA-232 serial ports (console, auxiliary port) |
|
Indicators |
Ethernet ports: RX and TX LEDs, link state, 10/100 indicator ATM ports: RX and TX LEDs, link state Route Processor: Status LED, fan and power supply operational LEDs PC card slot 0/1 LEDs, Ethernet RX and TX LEDs, link state |
|
Network Clock Module |
Two T1/E1 BITS interfaces DB-9 alarm connector Output clock at 19.44 MHz Local clock with Stratum-3 quality Free-run accuracy of +-4.6 * 10-6 Holdover stability +-0.37 ppm in 24 hours Bellcore GR1244 and GR253 compliant |
|
Description |
Specification |
|---|---|
|
Maximum power budget |
17.6A @ 100 VAC, 60 Hz, 14.6A @ 115 VAC, 60 Hz; 7A @ 230 VAC, 50 Hz with chassis fully configured |
|
Autosensing limits |
100-127/200-240 VAC, 8/4A, 47-63 Hz |
|
Description |
Specification |
|---|---|
|
Dimensions (H x W x D) |
25.25 x 17.3 x 18.25 in. (64.14 x 43.9 x 46.36 cm) |
|
Weight, empty |
70 lb (31.7 kg) |
|
Weight, loaded |
160 lb (72.5 kg) |
|
Route and switch processor dimensions (H x W x D) |
1.2 x 14.4 x 16.0 in. (3.0 x 36.6 x 40.6 cm) |
|
Line module dimensions (H x W x D) |
1.2 x 13.0 x 10.0 in. (3.0 x 33.0 x 25.4 cm) |
|
Altitude |
-500 to 10,000 ft (-52 to 304 m) |
|
Temperature |
32 to 104°F (0 to 40°C) |
|
Storage temperature |
-40 to 167°F (-40 to 75°C) |
|
Relative humidity |
10 to 90% noncondensing |
|
Description |
Specification |
|---|---|
|
Safety Certifications |
UL 1950 EN 60950 CSA-C22.2 No. 950-93Electromagnetic Emissions IEC 950 Network Equipment Building Systems (NEBS) Level 3 |
|
Electromagnetic Emissions Certificate |
FCC Part 15 (CFR 47) Class A N 55022 Class A with UTP and Class B with FTP CISPR 22 Class A with UTP and Class B with FTP VCCI Class A with UTP and Class B with FTP AS/NZS 3548 Class A with UTP and Class B with FTP |
|
Interface Modules |
Catalyst 8540 CSR |
|---|---|
|
High Density Fast Ethernet Line Cards |
Yes |
|
High Density Gigabit Ethernet Line Cards |
Yes |
|
OC-12c Packet-Over-SONET (POS) Uplink |
Yes |
|
OC-3c/OC-12c ATM Uplink |
Yes |
|
Line Card |
Media Options |
Maximum Switch Density |
|---|---|---|
|
16-Port Fast Ethernet |
10/100 UTP with RJ-45 connectors 100 BaseFX MMF with mini-MT connectors |
128 ports |
|
8-Port Gigabit Ethernet |
GBIC connectors Short wavelength (250 m) Long wavelength (500 m)Single mode (3 km) Extended Range (up to 100 km) |
64 ports |
|
Description |
Specification |
|---|---|
|
Technology |
Five-slot chassis and fan tray Optional redundant AC or DC, auto-sensing, load-sharing power supplies, each with its own power cord C8510-SRP module running L3 Cisco IOS software 10 Gbps shared memory, non-blocking fabric 16 MB of Flash memory standard, plus up to 20 MB through PC Flash cards 64 MB DRAM system memory Ethernet port for out-of-band management Dual EIA/TIA-232 serial ports (console, auxiliary port) |
|
Indicators |
Ethernet ports: RX and TX LEDs, link state, 10/100 indicator ATM ports: RX and TX LEDs, link state Route Processor: Status LED, fan and power supply operational LEDs PC card slot 0/1 LEDs, Ethernet RX and TX LEDs, link state |
|
Chassis Specifications |
Dimensions (H x W x D): 10.5 x 17.2 x 18.14 in. (26.7 x 43.7 x 46.1 cm); standard 19-in rack mount Empty weight: 43 lb (19.5 kg) Fully loaded weight: depends upon loading; approximately 85 lb (39 kg) PAM Dimensions (H x W x D): 1.2 x 6.5 x 10 in. (3.0 x 16.5 x 25.4 cm) Maximum power budget: 9.8A @ 115 VAC, 60 Hz 4.9A @ 230 VAC, 50 Hz Auto-sensing limits: 100-127/200-240 VAC, 8/4A, 847-63 Hz Maximum power budget: 14.0A maximum @ -48V |
|
Interface Modules |
Catalyst 8510 CSR |
|---|---|
|
Fast Ethernet Line Cards |
Yes |
|
Gigabit Ethernet Line Cards |
Yes |
|
Line Card |
Media Options |
Maximum Switch Density |
|---|---|---|
|
8-Port Fast Ethernet |
10/100 UTP with RJ-45 connectors 100 BaseFX MMF with SC connectors |
32 ports |
|
1-Port Gigabit Ethernet |
GBIC connectors Short wavelength (250m) Long wavelength (500m) Single mode (3 km) Extended Range (up to 100 km) |
4 ports |
For software specification information, access Cisco Connection Online at http://www.cisco.com
A typical configuration for the Catalyst 8540 CSR includes the following:
An 8540 CSR starter kit
Either AC or DC
Redundant power supplies (AC or DC) as required
Redundant Route Processor and Switch Processor as required
The latest Cisco IOS software image for Layer 3 switching
Country-specific power cord (CAB-7KA) included in chassis price
Layer 3 and ATM/POS Uplink interfaces as required
The Flash memory cards are not required for the operation of the Catalyst 8540 CSR and can only be ordered as spares. The Catalyst 8540 CSR RP use the same Flash memory PC Cards as the Route Switch Processor (RSP) of the Cisco 7000 series routers, the route switch module of the Catalyst 5000 family, or the LightStream 1010 ATM switch.
A typical configuration for the Catalyst 8510 CSR includes the following:
An 8510 CSR starter kit
Either AC or DC
Redundant power supplies (AC or DC) as required
Redundant Switch Route Processor as required
The latest Cisco IOS software image for Layer 3 switching
Country-specific power cord (CAB-7KA) included in chassis price
Layer 3 interfaces as required
The Flash memory cards are not required for the operation of the Catalyst 8510 CSR and can only be ordered as spares. The Catalyst 8510 CSR SRP use the same Flash memory PC Cards as the Route Switch Processor (RSP) of the Cisco 7000 series routers, the route switch module of the Catalyst 5000 family, or the LightStream 1010 Multiservice ATM switch.
Product and Part Numbers Table 20-48: Part Numbers for the Catalyst 8540 Series| Part Description | Part Number |
|---|---|
| Catalyst 8540 Base Common Equipment | |
| C8540 Chassis | C8540-CHAS13 |
| Catalyst 8540 - Chassis (spare) | C8540-CHAS13= |
| C8540 Power Supply - AC | C8540-PWR-AC |
| C8540 Power Supply - AC (spare) | C8540-PWR-AC= |
| C8540 Redundant Power Supply - AC | C8540-PWR-AC/2 |
| C8540 Power Supply - DC | C8540-PWR-DC |
| C8540 Power Supply - DC (spare) | C8540-PWR-DC= |
| C8540 Redundant Power Supply - DC | C8540-PWR-DC/2 |
| Catalyst 8540 Layer 3 Common Equipment | |
| Catalyst 8540 CSR Starter Kit with AC Power | C8540CSR-SKIT-AC |
| Catalyst 8540 CSR Starter Kit with DC Power | C8540CSR-SKIT-DC |
| Catalyst 8540 CSR Route Processor - Installed | C8541CSR-RP |
| Catalyst 8540 CSR Route Processor (spare) | C8541CSR-RP= |
| Catalyst 8540 CSR Redundant Switch Processor - Installed | C8541CSR-RP/2 |
| Catalyst 8540 CSR Switch Processor - Installed | C8542CSR-SP |
| Catalyst 8540 CSR Switch Processor (spare) | C8542CSR-SP= |
| Catalyst 8540 CSR Redundant Switch Processor | C8542CSR-SP/2 |
| Catalyst 8540 Multiservice Switched Common Equipment | |
| C8540 MSR Starter Kit w/ Stratum 4 Clock Module - AC Power | C8540MSR-SKIT-AC |
| C8540 MSR Starter Kit w/ Stratum 4 Clock Module - DC Power | C8540MSR-SKIT-DC |
| C8540 MSR Multiservice Route Processor | C8545MSR-MRP4CLK |
| C8540 MSR Multiservice Route Processor (spare) | C8545MSR-MRP4CLK= |
| C8540 MSR Redundant Multiservice Route Processor | C8545MSR-MRP4CLK/2 |
| C8540 MSR Route Processor Stratum 3 | C8545MSR-MRP3CLK |
| C8540 MSR Route Processor Stratum 3 (spare) | C8545MSR-MRP3CLK= |
| C8540 Redundant MSR Route Processor Stratum 3 | C8545MSR-MRP3CLK/2 |
| C8540 MSR - MRP Stratum 3 Clock - Upgrade | UPG-MSR-MRP-3CLK |
| C8540 MSR Switch Processor with ATM FC | C8546MSR-MSP-FCL |
| C8540 MSR Switch Processor with ATM FC (spare) | C8546MSR-MSP-FCL= |
| C8540 Redundant MSR Switch Processor with ATM FC | C8546MSR-MSP-FCL/2 |
| Catalyst 8540 Flash Memory Cards | |
| 8540MSR 20MB PC Flash Memory Card w/ default SW (spare) | MEM-8540M-FLC20M= |
| C8500/LS1010 PCMCIA Flash Memory Card 8 MB (spare) | MEM-ASP-FLC8M= |
| C8500/LS1010 PCMCIA Flash Memory Card 16 MB (spare) | MEM-ASP-FLC16M= |
| C8500/LS1010 PCMCIA Flash Memory Card 20 MB (spare) | MEM-ASP-FLC20M= |
| Catalyst 8540 Layer 3 Interface Modules (Gigabit Ethernet) | |
| C8540 2-port GE 16K | C85GE-2X-16K |
| C8540 2-port GE 16K (spare) | C85GE-2X-16K= |
| C8540 2-port GE 64K | C85GE-2X-64K |
| C8540 2-port GE 64K (spare) | C85GE-2X-64K= |
| C8540 2-port GE with ACL 16K | C85GE-2XACL-16K |
| C8540 2-port GE with ACL 16K (spare) | C85GE-2XACL-16K= |
| C8540 2-port GE with ACL 64K | C85GE-2XACL-64K |
| C8540 2-port GE with ACL 64K (spare) | C85GE-2XACL-64K= |
| C8540 8 port GE Module 64K | C85GE-8X-64K |
| C8540 8 port GE Module 64K (spare) | C85GE-8X-64K= |
| 1 Port ATM OC12 SMF-IR Uplink + 1 port GE 64K | C85-1OC12SGE-64K |
| 1 Port ATM OC12 SMF-IR Uplink + 1 port GE 256K | C85-1OC12SGE-256K |
| Catalyst 8540 Access Control List Daughter Card | C8540-ACL= |
| Catalyst 8540 Layer 3 Interface Modules (Fast Ethernet) | |
| C8540 16-port 10/100 RJ-45 16K | C85FE-16T-16K |
| C8540 16-port 10/100 RJ-45 16K (spare) | C85FE-16T-16K= |
| C8540 16-port 10/100 RJ-45 64K | C85FE-16T-64K |
| C8540 16-port 10/100 RJ-45 64K (spare) | C85FE-16T-64K= |
| C8540 16 port 10/100 RJ45 w/ ACL 16K | C85FE-16TACL-16K |
| C8540 16-port 10/100 RJ-45 w/ACL 16K (spare) | C85FE-16TACL-16K= |
| C8540 16-port 10/100 RJ45 w/ ACL 64K | C85FE-16TACL-64K |
| C8540 16-port 10/100 RJ-45 w/ ACL 64K (spare) | C85FE-16TACL-64K= |
| C8540 16-port 100-FX MT-RJ 16K | C85FE-16F-16K |
| C8540 16-port 100-FX MT-RJ 16K (spare) | C85FE-16F-16K= |
| C8540 16-port 100-FX MT-RJ 64K | C85FE-16F-64K |
| C8540 16-port 100-FX MT-RJ 64K (spare) | C85FE-16F-64K= |
| C8540 16-port 100-FX MT-RJ w/ ACL 16K | C85FE-16FACL-16K |
| C8540 16-port 100-FX MT-RJ w/ACL 16K (spare) | C85FE-16FACL-16K= |
| C8540 16-port 100-FX MT-RJ w/ ACL 64K | C85FE-16FACL-64K |
| C8540 16-port 100 MT-RJ w/ACL 64K (spare) | C85FE-16FACL-64K= |
| Catalyst 8540 Access Control List Daughter Card | C8540-ACL= |
| Catalyst 8540 ATM Router Module | |
| C8540 ATM Router Module 64K | C8540-ARM-64K |
| C8540 ATM Router Module 64K (spare) | C8540-ARM-64K= |
| Catalyst 8540 ATM Interface Modules | |
| C8540 2 Port OC-48c SMF-IR | C85MS-2F-OC48SS |
| C8540 2 Port OC-48c SMF-IR (spare) | C85MS-2F-OC48SS= |
| C8540 1 Port OC-48c SMF-IR + 4 x OC-12 SMF-IR | C85MS-1F4S-OC48SS |
| C8540 1 Port OC-48c SMF-IR + 4 x OC-12 SMF-IR (spare) | C85MS-1F4S-OC48SS= |
| C8540 1 Port OC-48c SMF-IR + 4 x OC-12 MMF | C85MS-1F4M-OC48SS |
| C8540 1 Port OC-48c SMF-IR + 4 x OC-12 MMF (spare) | C85MS-1F4M-OC48SS= |
| C8540 4-port OC-12 MMF | C85MS-4F-OC12MM |
| C8540 4-port OC-12 MMF (spare) | C85MS-4F-OC12MM= |
| 8540MSR 4-port OC-12 SMF Intermediate Reach - install | C85MS-4F-OC12SS |
| 8540MSR 4-port OC-12 SMF Intermediate Reach - Spare | C85MS-4F-OC12SS= |
| Cat 8540 MSR - 16-port OC-3 MMF - Installed | C85MS-16F-OC3MM |
| Cat 8540 MSR - 16-port OC-3 MMF - Spare | C85MS-16F-OC3MM= |
| Catalyst 8540 ATM Carrier Modules (required for PAMs) | |
| C8540 SuperCAM for Port Adapter Modules (PAMs) | C85MS-SCAM-2P |
| C8540 SuperCAM for Port Adapter Modules (spare) | C85MS-SCAM-2P= |
| Catalyst 8540 Port Adapter Modules (Voice) | |
| 4 Port T1 (circuit emulation) RJ-48 PAM | WAI-T1C-4RJ48 |
| 4 Port T1 (circuit emulation) RJ-48 PAM (spare) | WAI-T1C-4RJ48= |
| 4 Port E1 (circuit emulation) BNC PAM | WAI-E1C-4BNC |
| 4 Port E1 (circuit emulation) BNC PAM (spare) | WAI-E1C-4BNC= |
| 4 Port E1 (circuit emulation) RJ-48 PAM | WAI-E1C-4RJ48 |
| 4 Port E1 (circuit emulation) RJ-48 PAM (spare) | WAI-E1C-4RJ48= |
| Catalyst 8540 Port Adapter Modules (Frame Relay) | |
| C8500 1-port Channelized DS3 Frame-relay PAM | C85MS-1DS3-FRBNC |
| C8500 1-port Channelized DS3 Frame-relay PAM (spare) | C85MS-1DS3-FRBNC= |
| C8500 4-port E1 Frame-Relay/FUNI PAM | C85MS-4E1-FRRJ48 |
| C8500 4-port E1 Frame-Relay/FUNI PAM (spare) | C85MS-4E1-FRRJ48= |
| Catalyst 8540 Port Adapter Modules (ATM) | |
| 4 Port STS-3c/STM-1 UTP-5 PAM | WAI-OC3-4U5 |
| 4 Port STS-3c/STM-1 UTP-5 PAM (spare) | WAI-OC3-4U5= |
| 4 Port OC-3c/STM-1 MMF PAM | WAI-OC3-4MM |
| 4 Port OC-3c/STM-1 MMF PAM (spare) | WAI-OC3-4MM= |
| 4 Port OC-3c/STM-1 SMF-IR PAM | WAI-OC3-4SS |
| 4 Port OC-3c/STM-1 SMF-IR PAM (spare) | WAI-OC3-4SS= |
| OC-3c/STM-1 Mix PAM, 1-port SMF-IR + 3-port MMF | WAI-OC3-1S3M |
| OC-3c/STM-1 Mix PAM, 1-port SMF-IR + 3-port MMF (spare) | WAI-OC3-1S3M= |
| 4-port OC-3c/STM-1 SMF-LR PAM | WAI-OC3-4SSLR |
| 4-port OC-3c/STM-1 SMF-LR PAM (spare) | WAI-OC3-4SSLR= |
| 1 Port OC-12c/STM-4c MMF PAM | WAI-OC12-1MM |
| 1 Port OC-12c/STM-4c MMF PAM (spare) | WAI-OC12-1MM= |
| 1 Port OC-12c/STM-4c SMF-IR PAM | WAI-OC12-1SS |
| 1 Port OC-12c/STM-4c SMF-IR PAM (spare) | WAI-OC12-1SS= |
| 1 Port OC-12c/STM-4c SMF-LR PAM | WAI-OC12-1SSLR |
| 1 Port OC-12c/STM-4c SMF-LR PAM (spare) | WAI-OC12-1SSLR= |
| 4 Port DS-3 PAM | WAI-T3-4BNC |
| 4 Port DS-3 PAM (spare) | WAI-T3-4BNC= |
| 4 Port E3 BNC PAM | WAI-E3-4BNC |
| 4 Port E3 BNC PAM (spare) | WAI-E3-4BNC= |
| 4 Port T1 (ATM) RJ-48 PAM | WAI-T1-4RJ48 |
| 4 Port T1 (ATM) RJ-48 PAM (spare) | WAI-T1-4RJ48= |
| 4 Port E1 (ATM) BNC PAM | WAI-E1-4BNC |
| 4 Port E1 (ATM) BNC PAM (spare) | WAI-E1-4BNC= |
| 4 Port E1 (ATM) RJ-48 PAM | WAI-E1-4RJ48 |
| 4 Port E1 (ATM) RJ-48 PAM (spare) | WAI-E1-4RJ48= |
| Catalyst 8540 Layer 3 Software Options | |
| Catalyst 8540 IP and Bridging Base Software (spare) | SRW-8540CSR2-0= |
| Catalyst 8540 IP and Bridging Base Software | S854R3-12.0.4W |
| Catalyst 8540 IP and Bridging Base Software (spare) | S854R3-12.0.4W= |
| Catalyst 8540 IP and Bridging Base Software | S854R3-12.0.5W |
| Catalyst 8540 Layer 3 Feature Licenses | |
| Catalyst 8540 IPX/AppleTalk Software License | FR-8540CSR-IPX |
| Catalyst 8540 IPX/AppleTalk Software License - Spare | FR-8540CSR-IPX= |
| Catalyst 8540 ATM Software Options | |
| Catalyst 8540 Integrated ATM and Layer 3 feature set | S854R2-12.0.7W |
| Catalyst 8540 Integrated ATM and Layer 3 feature set | S854R2-12.0.7W= |
| Catalyst 8540 Integrated ATM and Layer 3 feature set | S854R2-12.0.4W |
| Catalyst 8540 Integrated ATM and Layer 3 feature set | S854R2-12.0.4W= |
| C8540 IISP and PNNI Feature Set (spare) | SRW-8540MSR5-5= |
| C8540 IISP and PNNI Feature Set | SRF-8540MSR5-9 |
| C8510 IISP and PNNI Feature Set (spare) | SRW-8540MSR5-9= |
| Catalyst 8540 Integrated ATM & Layer 3 feature set | S854R2-12.0.10W |
| Catalyst 8540 IP and Bridging Base Software | S854R3-12.0.10W |
| Catalyst 8540 ATM Software Feature License Options | |
| Cat 8540MSR - Hierarchical PNNI License | FR-8540MSR-HPNNI |
| Cat 8540MSR - Hierarchical PNNI License | FR-8540MSR-HPNNI= |
| Cat 8540MSR - Tag Switching License | FR-8540MSR-TAGSW |
| Cat 8540MSR - Tag Switching License | FR-8540MSR-TAGSW= |
| Cat 8540MSR - Hierarchical PNNI + Tag Switching License | FR-8540MSR-THPNNI |
| Cat 8540MSR - Hierarchical PNNI + Tag Switching License | FR-8540MSR-THPNNI= |
| Catalyst 8540 Miscellaneous | |
| Spare EMI clips for E1C, E1, or E3-BNC PAMs | CLP-ATM-EMI-BNC-E= |
| ATM25 Cable, 96 Pin T12 Male RJ45`s | CAB-ATM25-12= |
| Catalyst 5000 Family Center Rack Mount Kit | WS-C5097= |
| 1000BASE-SX "Short Wavelength" GBIC (Multimode only) | WS-G5484 |
| 1000BASE-LX/LH "long haul" GBIC (singlemode or multimode) | WS-G5486 |
| MT-RJ MM to SC Duplex MM - 1 meter | CAB-MTRJ-SC-MM-1M= |
| MT-RJ MM to ST Duplex MM - 1 meter | CAB-MTRJ-ST-MM-1M= |
| MT-RJ MM to SC Duplex MM - 3 meter | CAB-MTRJ-SC-MM-3M= |
| MT-RJ MM to ST Duplex MM - 3 meter | CAB-MTRJ-ST-MM-3M= |
| MT-RJ MM to SC Duplex MM - 5 meter | CAB-MTRJ-SC-MM-5M= |
| MT-RJ MM to ST Duplex MM - 5 meter | CAB-MTRJ-ST-MM-5M= |
| 8-to-16MB Flash Upgrade for the Catalyst 8500 Series (spare) | C85-SIMM-16MB= |
| Part Description | Part Number |
|---|---|
| Catalyst 8510 Base Common Equipment | |
| Catalyst 8510 Chassis | C8510-CHAS5 |
| Catalyst 8510 Chassis (spare) | C8510-CHAS5= |
| Catalyst 8510 AC Power Supply | C8510-PWR-AC |
| Catalyst 8510 AC Power Supply (spare) | C8510-PWR-AC= |
| Catalyst 8510 Redundant AC Power Supply | C8510-PWR-AC/2 |
| Catalyst 8510 DC Power Supply | C8510-PWR-DC |
| Catalyst 8510 DC Power Supply (spare) | C8510-PWR-DC= |
| Catalyst 8510 Redundant DC Power Supply | C8510-PWR-DC/2 |
| C8510CSR Starter Kit with AC Power | C8510CSR-SKIT-AC |
| C8510CSR Starter Kit with DC Power | C8510CSR-SKIT-DC |
| C8510 MSR Starter Kit with AC Power | C8510MSR-SKIT-AC |
| C8510MSR Starter Kit with DC Power | C8510MSR-SKIT-DC |
| Catalyst 8510 CSR Common Equipment | |
| C8510 CSR Switch Route Processor | C8510-SRP |
| C8510 CSR Switch Route Processor (spare) | C8510-SRP= |
| Catalyst 8510 MSR Common Equipment | |
| C8510 MSR Switch Route Processor | C8515-MSRP |
| C8510 MSR Switch Route Processor (spare) | C8515-MSRP= |
| Catalyst 8510 Flash Memory Cards | |
| C8500/LS1010 PCMCIA Flash Memory Card 8 MB (spare) | MEM-ASP-FLC8M= |
| C8500/LS1010 PCMCIA Flash Memory Card 16 MB (spare) | MEM-ASP-FLC16M= |
| C8500/LS1010 PCMCIA Flash Memory Card 20 MB (spare) | MEM-ASP-FLC20M= |
| Catalyst 8510 Layer 3 Interface Modules (Gigabit Ethernet) | |
| C8510 1-Port GE 16K | C85GE-1X-16K |
| C8510 1-Port GE 16K (spare) | C85GE-1X-16K= |
| C8510 1-Port GE 64K | C85GE-1X-64K |
| C8510 1-Port GE 64K (spare) | C85GE-1X-64K= |
| Catalyst 8510 Layer 3 Interface Modules (Fast Ethernet) | |
| C8510 8-Port 10/100 RJ45 16K | C85FE-8T-16K |
| C8510 8-Port 10/100 RJ45 16K (spare) | C85FE-8T-16K= |
| C8510 8-Port 10/100 RJ45 64K | C85FE-8T-64K |
| C8510 8-Port 10/100 RJ45 64K (spare) | C85FE-8T-64K= |
| C8510 8-Port 100-FX MT-RJ 16K | C85FE-8F-16K |
| C8510 8-Port 100-FX MT-RJ 16K (spare) | C85FE-8F-16K= |
| C8510 8-Port 100-FX MT-RJ 64K | C85FE-8F-64K |
| C8510 8-Port 100-FX MT-RJ 64K (spare) | C85FE-8F-64K= |
| Catalyst 8510 Carrier Modules (required for PAMs) | |
| LightStream 1010/C5500 Carrier Module (installed) | WATM-CAM-2P |
| LightStream 1010/C5500 Carrier Module (spare) | WATM-CAM-2P= |
| LightStream 1010/C5500 Carrier Module Slot Cover (spare) | WATM-CAM-CVR= |
| Port Adapter Module Slot Cover (Spare) | WAI-CVR= |
| Catalyst 8500/LightStream 1010 PAMs (Voice) | |
| 4 Port T1 (circuit emulation) RJ-48 PAM | WAI-T1C-4RJ48 |
| 4 Port T1 (circuit emulation) RJ-48 PAM (spare) | WAI-T1C-4RJ48= |
| 4 Port E1 (circuit emulation) BNC PAM | WAI-E1C-4BNC |
| 4 Port E1 (circuit emulation) BNC PAM (spare) | WAI-E1C-4BNC= |
| 4 Port E1 (circuit emulation) RJ-48 PAM | WAI-E1C-4RJ48 |
| 4 Port E1 (circuit emulation) RJ-48 PAM (spare) | WAI-E1C-4RJ48= |
| Catalyst 8500/LightStream 1010 PAMs (Frame Relay) | |
| C8500 1-port Channelized DS3 Frame-relay PAM | C85MS-1DS3-FRBNC |
| C8500 1-port Channelized DS3 Frame-relay PAM (spare) | C85MS-1DS3-FRBNC= |
| C8500 4-port E1 Frame-Relay/FUNI PAM | C85MS-4E1-FRRJ48 |
| C8500 4-port E1 Frame-Relay/FUNI PAM (spare) | C85MS-4E1-FRRJ48= |
| Cat 8500 -- LightStream 1010 PAMs ATM | |
| 1 Port OC-12c/STM-4c SMF-LR PAM | WAI-OC12-1SSLR |
| 1 Port OC-12c/STM-4c SMF-LR PAM (spare) | WAI-OC12-1SSLR= |
| 1 Port OC-12c/STM-4c SMF-IR PAM | WAI-OC12-1SS |
| 1 Port OC-12c/STM-4c SMF-IR PAM (spare) | WAI-OC12-1SS= |
| 1 Port OC-12c/STM-4c MMF PAM | WAI-OC12-1MM |
| 1 Port OC-12c/STM-4c MMF PAM (spare) | WAI-OC12-1MM= |
| 4-port OC-3c/STM-1 SMF-LR PAM | WAI-OC3-4SSLR |
| 4-port OC-3c/STM-1 SMF-LR PAM (spare) | WAI-OC3-4SSLR= |
| 4 Port OC-3c/STM-1 SMF-IR PAM | WAI-OC3-4SS |
| 4 Port OC-3c/STM-1 SMF-IR PAM (spare) | WAI-OC3-4SS= |
| OC-3c/STM-1 Mix PAM, 1-port SMF-IR + 3-port MMF | WAI-OC3-1S3M |
| OC-3c/STM-1 Mix PAM, 1-port SMF-IR + 3-port MMF (spare) | WAI-OC3-1S3M= |
| 4 Port OC-3c/STM-1 MMF PAM | WAI-OC3-4MM |
| 4 Port OC-3c/STM-1 MMF PAM (spare) | WAI-OC3-4MM= |
| 4 Port STS-3c/STM-1 UTP-5 PAM | WAI-OC3-4U5 |
| 4 Port STS-3c/STM-1 UTP-5 PAM (spare) | WAI-OC3-4U5= |
| 4 Port DS-3 PAM | WAI-T3-4BNC |
| 4 Port DS-3 PAM (spare) | WAI-T3-4BNC= |
| 4 Port E3 BNC PAM | WAI-E3-4BNC |
| 4 Port E3 BNC PAM (spare) | WAI-E3-4BNC= |
| 4-port ATM 25 PAM - note C8510/LS1010 only | C85MS-ATM25-4P |
| 4-port ATM 25 PAM - note C8510/LS1010 only (spare) | C85MS-ATM25-4P= |
| C8500MSR/LS1010 8-port TI IMA PAM | C85MS-8T1-IMA |
| C8500MSR/LS1010 8-port TI IMA PAM (spare) | C85MS-8T1-IMA= |
| C8500MSR/LS1010 8-port E1 120 ohm IMA PAM | C85MS-8E1-IMA-120 |
| C8500MSR/LS1010 8-port E1 120 ohm IMA PAM (spare) | C85MS-8E1-IMA-120= |
| 4 Port T1 (ATM) RJ-48 PAM | WAI-T1-4RJ48 |
| 4 Port T1 (ATM) RJ-48 PAM (spare) | WAI-T1-4RJ48= |
| 4 Port E1 (ATM) RJ-48 PAM | WAI-E1-4RJ48 |
| 4 Port E1 (ATM) RJ-48 PAM (spare) | WAI-E1-4RJ48= |
| 4 Port E1 (ATM) BNC PAM | WAI-E1-4BNC |
| 4 Port E1 (ATM) BNC PAM (spare) | WAI-E1-4BNC= |
| Catalyst 8510 Layer 3 Software Options | |
| Cat 8510 IP and Bridging Feature Set 12.0T - Spare | SRW-8510CSR1-1= |
| C8510 IP and Bridging feature set | SRF-8510CSR2-0 |
| C8510 IP and Bridging feature set (spare) | SRW-8510CSR2-0= |
| C8510 IP and bridging feature set | S851R3-12.0.4W |
| C8510 IP and bridging feature set | S851R3-12.0.7W |
| Catalyst 8510 Layer 3 Feature Licenses | |
| C8510 IPX/AppleTalk Feature Set | FR-8510CSR-IPX |
| C8510 IPX/AppleTalk Feature Set (spare) | FR-8510CSR-IPX= |
| Catalyst 8510 ATM Software Options | |
| C8510 IISP and PNNI Feature Set | SRF-8510MSR5-5 |
| C8510 IISP and PNNI Feature Set | SRF-8510MSR5-9 |
| C8510 IISP and PNNI Feature Set (spare) | SRW-8510MSR5-9= |
| C8510 ATM Software | S851R2-12.0.4W |
| C8510 ATM Software | S851R2-12.0.4W= |
| C8510 MSR 12.0.7 Maintenance Release | S851R2-12.0.7W |
| Catalyst 8510 Integrated ATM & Layer 3 feature set | S851R2-12.0.10W |
| Catalyst 8510 IP and Bridging Base Software | S851R3-12.0.10W |
| Catalyst 8510 ATM Software Feature License Options | |
| C8510 Hierarchical PNNI Upgrade License | FR-8510-HPNNI |
| C8510 Hierarchical PNNI Upgrade License (spare) | FR-8510-HPNNI= |
| C8510 Tag Switching Upgrade License | FR-8510-TAGSW |
| C8510 Tag Switching Upgrade License (spare) | FR-8510-TAGSW= |
| C8510 Hierarchical PNNI + Tag Switching Upgrade | FR-8510-THPNNI |
| C8510 Hierarchical PNNI + Tag Switching (spare) | FR-8510-THPNNI= |
| Catalyst 8510 Miscellaneous | |
| Spare EMI clips for E1C, E1, or E3-BNC PAMs | CLP-ATM-EMI-BNC-E= |
| ATM25 Cable, 96 Pin T12 Male RJ45`s | CAB-ATM25-12= |
| Catalyst 5000 Family Center Rack Mount Kit | WS-C5097= |
| 1000BASE-SX "Short Wavelength" GBIC (Multimode only) | WS-G5484 |
| 1000BASE-LX/LH "long haul" GBIC (singlemode or multimode) | WS-G5486 |
| MT-RJ MM to SC Duplex MM - 1 meter | CAB-MTRJ-SC-MM-1M= |
| MT-RJ MM to SC Duplex MM - 3 meter | CAB-MTRJ-SC-MM-3M= |
| MT-RJ MM to SC Duplex MM - 5 meter | CAB-MTRJ-SC-MM-5M= |
| MT-RJ MM to ST Duplex MM - 1 meter | CAB-MTRJ-ST-MM-1M= |
| MT-RJ MM to ST Duplex MM - 3 meter | CAB-MTRJ-ST-MM-3M= |
| MT-RJ MM to ST Duplex MM - 5 meter | CAB-MTRJ-ST-MM-5M= |